Do you have a question about the Lux Products PurePro Everything'Stat DP722 and is the answer not in the manual?
Brand | Lux Products |
---|---|
Model | PurePro Everything'Stat DP722 |
Category | Thermostat |
Language | English |
Details the number of heat stages the thermostat supports.
Specifies the number of cooling or compressor stages supported.
Lists the voltage and current ratings for thermostat terminals.
Lists the necessary tools for thermostat installation.
Provides guidelines for choosing an optimal installation location.
Step-by-step instructions for safely removing the existing thermostat.
Guidance on physically attaching the thermostat base to the wall.
General section covering thermostat wiring connections and diagrams.
Explains the function of each terminal on the thermostat base.
Details how to configure freeze protection using thermostat settings.
Highlights important wiring considerations for specific system types.
Presents typical wiring configurations for various HVAC systems.
Maps old thermostat wiring labels to new thermostat terminals for single-stage heat.
Maps old thermostat wiring labels to new thermostat terminals for single-stage cool.
Wiring cross-reference for combined single-stage heating and cooling.
Wiring cross-reference for 2-stage heat, 1-stage cool heat pump systems.
Visual diagrams illustrating various system wiring hookups.
Instructions for installing the thermostat's backup batteries.
Overview of the installer setup menu for system configuration.
Steps to enter and navigate the installer setup menu.
Setting to define the HVAC system type (furnace or heat pump).
Configures the number of heat stages for the system.
Configures the number of compressor stages for cooling or heat pumps.
Selects available operating modes for the thermostat.
Sets compressor protection minimum run time.
Enables disabling heat pump below a set outdoor temperature.
Sets the temperature at which heat pump lockout occurs.
Defines the temperature difference for auto-changeover.
Sets temperature differential for first stage heating/cooling control.
Sets temperature differential for second stage heating/cooling control.
Configures fan control behavior for heating systems.
Programs delay for fan activation after heating starts.
Programs delay for fan deactivation after heating stops.
Programs delay for fan activation after cooling starts.
Programs delay for fan deactivation after cooling stops.
Enables or disables the use of an outdoor temperature sensor.
Enables or disables the thermostat's internal temperature sensor.
Enables or disables remote indoor sensors for averaging.
Table detailing installer setup options for furnace systems.
Table detailing installer setup options for heat pump systems.
Final steps and verification after installation.
Introduction to basic thermostat operation and controls.
How to use arrow keys to adjust settings.
Detailed steps for adjusting temperature set points.
Methods for changing various thermostat settings.
Instructions for setting the current day and time.
Overview of the factory-set default temperature program.
Explanation of available system operating modes.
How to temporarily override programmed settings.
How to set a permanent temperature hold.
How the thermostat automatically switches between heat and cool.
How to operate the thermostat in heating mode.
How to operate the thermostat in cooling mode.
How to turn the thermostat off.
How to activate and manage the display backlight.
Overview of user-configurable settings.
Steps to enter and navigate the user setup menu.
How to lock the thermostat keypad to prevent changes.
Details on setting a partial keypad lock.
Details on setting a full keypad lock.
Step-by-step guide to setting keypad lock codes.
Instructions for unlocking the thermostat keypad.
How to change the existing keypad lock code.
Option to enable or disable audible button feedback.
How to select Fahrenheit or Celsius display.
How to choose between 12-hour and 24-hour clock format.
How to adjust thermostat temperature calibration.
Sets the highest allowable heat temperature set point.
Sets the lowest allowable cool temperature set point.
Explains how the thermostat learns to reach setpoints efficiently.
Sets a reminder for changing the HVAC air filter.
Table summarizing user setup menu options and defaults.
Covers advanced thermostat features and operational modes.
How to activate and use the emergency heat function.
Explanation of available fan operating modes (Auto, Clean, On).
How the fan operates automatically with heating/cooling.
Details the CLEAN CYCLE® feature for continuous fan operation.
How to set the fan to run continuously.
How to set a fixed temperature for extended periods away.
How to adjust the thermostat for Daylight Saving Time.
How to check and reset the air filter timer.
How to view cumulative heating and cooling run times.
Information on installing and using an optional outdoor sensor.
Information on installing and using optional remote indoor sensors.
Information on hardware and software reset procedures.
How to perform a hardware reset of the thermostat.
How to perform a software reset to default settings.
How to program daily temperature and fan schedules.
Steps to program weekday temperature schedules.
Steps to program weekday fan schedules.
Steps to program weekend temperature and fan schedules.
How to copy programmed schedules between days.
Instructions for replacing the thermostat's batteries.
Explains how heating and cooling stages are activated.