What to do if my Luxman Receiver display lights, but there's no sound or picture?
If your Luxman Receiver's display lights up, but you're not getting any sound or picture, there are a few things you can check: * Ensure all input and speaker connections are securely connected. * Verify that the mute function is not enabled by pressing the Mute button. * Increase the volume level using the volume control.
Why is there no sound from any speaker and the light around power switch is red on my Luxman 7.1 Channel Reciever LR-8500 Receiver?
If there's no sound from any speaker and the power switch light is red, your Luxman Receiver might be in protection mode. This could be due to a short in the speaker wire connections. Check the speaker wire connections for shorts at both the receiver and speaker ends.
What to do if my Luxman 7.1 Channel Reciever LR-8500 does not respond to remote commands?
If your Luxman Receiver isn't responding to the remote, try these steps: * Replace the batteries in the remote. * Ensure the correct device is selected by pressing the FUNCTION buttons. * Make sure the front-panel sensor on the receiver is visible to the remote, or connect the remote sensor.
How to fix Luxman Receiver if it does not function when the Main Power Switch is pushed?
If your Luxman Receiver isn't turning on when you push the Main Power Switch, make sure the AC power cord is plugged into a working outlet. Also, check if the outlet is controlled by a switch.
Why is there no sound from surround or center speakers on my Luxman 7.1 Channel Reciever LR-8500 Receiver?
If you're not getting sound from the surround or center speakers on your Luxman Receiver, consider the following: * Ensure you've selected a surround mode other than Stereo. * Be aware that monaural inputs don't provide surround information. * Check the speaker mode configuration. * Note that stereo or mono program material might not generate center- or rear-channel information from nonencoded programs.
What to do if letters flash in the channel indicator display and digital audio stops on Luxman 7.1 Channel Reciever LR-8500 Receiver?
If letters are flashing in the channel indicator display and the digital audio stops on your Luxman Receiver, it might be because the digital audio feed is paused. Try resuming play for the DVD. Also, ensure that Digital Input is selected.
Why the Luxman 7.1 Channel Reciever LR-8500 Receiver turns on, but the front-panel display does not light up?
If your Luxman Receiver turns on but the front-panel display doesn't light up, the display brightness might be turned off. Follow the instructions in the Display Mode section of the manual to set the display to FULL.
How to stop intermittent buzzing in tuner of Luxman 7.1 Channel Reciever LR-8500?
To address intermittent buzzing in the tuner of your Luxman Receiver, try moving the unit or antenna away from potential sources of interference such as computers, fluorescent lights, motors, or other electrical appliances.
Covers general safety advice including mains plug, liquids, ventilation, and electrical shock.
General precautions for operation, ventilation, voltage, location, and initial connections.
Explains memory preservation and the procedure for resetting the unit.
Explains various digital and matrix surround sound audio technologies.
Details Dolby Digital, Dolby Digital EX, and Dolby Pro Logic IIx audio technologies.
Provides recommendations for optimal placement of front, center, and surround speakers.
Instructions for connecting surround back speakers, subwoofer, and speaker wires.
Details connections for speakers, pre-outs, AC outlets, RS-232C, and Zone II audio.
Guides for connecting analog and digital audio components and sources.
Details video connections, including composite, S-Video, and component inputs.
Guides for connecting multi-channel sources, external amplifiers, and IR control devices.
Instructions for connecting FM/AM antennas, including assembly of the AM loop antenna.
Details the functions of the LR-8500's front panel controls and indicators.
Explains the meaning of the indicators on the unit's display panel.
Covers the functions and buttons of the main remote control unit.
Details the functions and buttons of the remote control unit for Zone II operation.
Guides on selecting inputs, muting, and tuning stations.
Guides on selecting audio/video sources and adjusting volume.
Explains how to select input sources and adjust the overall listening level.
Details how to temporarily mute sound and adjust bass/treble settings.
Describes how to set the receiver to automatically turn off after a specified time.
Instructions on how to choose and adjust various surround sound modes.
Explains how to use Night Mode to compress dynamic range for listening.
Guides on activating the audio feed to a remote room via main or Zone II remote.
Guides for setting speaker sizes, crossover points, and overall system configuration.
Explains how to use the test tone function to adjust relative speaker volume levels.
Guides on setting speaker distances for proper delay compensation.
Details on selecting stations, tuning, and storing favorite radio presets.
Explains RDS features and how to search for stations by Program Type.
Guides on selecting and playing video sources like DVD, VCR, etc.
Guides on navigating the OSD menu for system setup and adjustments.
Explains how to configure input functions, digital polling, and various surround modes.
Describes theater modes and Dolby Surround specific adjustments.
Guides for setting speaker sizes and crossover points for optimal audio.
Guides on setting speaker distances and adjusting individual channel output levels.
Details on display timeout, display mode, default volume, and OSD settings.
Guides for configuring the LR-8500 for Zone II operation, including input and volume.
Instructions for using the automated speaker setup and system calibration process.
Step-by-step guide for performing the Room Auto Setup using the microphone.
Explains the results and checks performed during the Room Auto Setup process.
Guides on programming the remote to control other audio/video equipment.
List of codes for programming the remote to control VCRs.
List of codes for programming the remote to control Satellite receivers.
List of codes for programming the remote to control TVs.
Further codes for programming the remote to control TVs.
Final codes for programming the remote to control TVs.
Lists common operational problems and their corresponding causes and solutions.
Technical specifications for amplifier, AM/FM tuners, video, and general components.
To Next Page
General