Magic-Pak EWC V Series User Manual

507390-01 Page 1 of 5Issue 1733
Save these instructions for future reference
(P) 507390-01
*P507390-01*
Manufactured By
Allied Air Enterprises LLC
A Lennox International, Inc. Company
215 Metropolitan Drive
West Columbia, SC 29170
This manual must be left with the homeowner for future reference.
This is a safety alert symbol and should never be ignored. When you see this symbol on labels or in
manuals, be alert to the potential for personal injury or death.
Improper installation, adjustment, alteration, service
or maintenance can cause property damage, personal
injury or loss of life. Installation and service must be
performed by a licensed professional installer (or
equivalent), service agency or the gas supplier.
WARNING
For your safety, do not store or use gasoline or other
ammable vapors and liquids in the vicinity of this or any
other appliance. Such actions could result in property
damage, personal injury, or death.
WARNING
These units are not approved for mobile home
applications. Such use could result in property damage,
personal injury, or death.
WARNING
Installation shall be made in accordance with the
requirements of the local utility and other authorities
having jurisdiction, or with the National Fuel Gas
Code, ANSI Z223.1 (latest edition) and the National
Electrical Code. Any alteration of internal wiring will void
certication and warranties.
CAUTION
INSTALLATION INSTRUCTIONS
EWC V-Series
TM
Models
Installation and servicing of air conditioning equipment
can be hazardous due to internal refrigerant pressure
and live electrical components. Only trained and
qualied service personnel should install or service
this equipment. Installation and service performed by
unqualied persons can result in property damage,
personal injury or death.
WARNING

Magic-Pak EWC V Series Specifications

General

Brand	Magic-Pak
Model	EWC V Series
Category	Air Conditioner
Language	English

Summary

General Safety Information

Safety Alert Symbol Explanation

Indicates potential for personal injury or death. Always be alert to this symbol.

Installation and Service Hazards

Improper installation or servicing can cause property damage, injury, or death.

Flammable Vapors Warning

Do not store or use gasoline or flammable liquids near the appliance.

Installation Compliance Standards

Installation must meet local utility, jurisdiction, and code requirements.

Mobile Home Application Exclusion

Units are not approved for mobile home applications; use may cause damage or injury.

Installation and Location Guidelines

General Unit Description

Unit is a self-contained electric heating/cooling unit examined for compliance.

Shipping Inspection

Check for shipping damage, note it on the bill, and file claims with the carrier.

Approved Installation Location

Unit approved for indoor installation only; service access must be inside.

Chassis Hold Down Brackets

Remove chassis hold down brackets from the outdoor side before installation.

Installation Methods and Connections

Installing Without a Wall Sleeve

Prepare a square opening, provide support, and seal the unit to the building.

Installing With a Wall Sleeve

Install sleeve, ensure gasket integrity, seal to building, and seat unit.

Condensate Drain Installation

Connect drain tube, ensure proper pitch, and test for free drainage.

Electrical Connection Requirements

Wire according to NEC/local codes; alterations void warranty.

Thermostat Installation

Install thermostat on an inside wall away from drafts for accurate temperature.

Operation and Maintenance

Air Filter Maintenance

Clean the permanent filter regularly for efficient operation.

Ductwork Guidelines

Provide adequately sized ductwork and use flexible connections to prevent noise.

Prohibited Adjustments

No adjustments should be made to cooling chassis or electric heating components.

Unit Operation Modes

Automatic operation provides heating or cooling based on thermostat settings.

Heating Operation Setup

Turn on power, set system switch to HEAT, and select desired temperature.

Cooling Operation Setup

Set system switch to COOL and select desired temperature.

Blower Operation Modes

Blower operates continuously if fan switch is ON, or cycles with thermostat in AUTO.

Unit Shutdown Procedure

Set system switch to OFF for temporary shutdown; turn off power for prolonged periods.

Maintenance Procedures

Cooling Chassis Maintenance

Periodic maintenance includes cleaning filters and condenser coil; motors are lubricated.

Cooling Chassis Removal and Re-installation

Procedure for safely removing and re-installing the cooling chassis for servicing.

Heating Section Maintenance

No maintenance is necessary for the electric heating elements.