Magic Vac Maxima 2 - Page 41

s-AKESURETHE3EALING"ARTHE Airtight Gasket (7) and Sealing Gasket (9) are
not dirty.
s4HEMAGIC VAC
®
bag may be punctured. To check, seal the bag with air inside,
place it under water and squeeze. If you see bubbles, there is a leak. Reseal or
use another bag.
MAGIC VAC
®
does not
correctly seal the bag
sWhen you can’t completely seal the bag, press the “sealing mode” button (2M)
and increase the sealing time.
s)FTHESealing Bar (6) overheats and melts the bag, lift the Cover (5) and allow the
Sealing Bar (6) to cool for a few minutes.
s#HECKTHEPOSITIONANDINTEGRITYOFTHESealing Gasket (9)
s)FLIQUIDSESCAPEDURINGTHEVACUUMPACKINGPHASEREMEMBERTHATTHEYMUSTFIRST
be refrigerated.
The MAGIC VAC
®
bag
doesn't maintain its
vacuum after sealing
s,EAKSALONGTHESEALCANBECAUSEDBYWRINKLESCRUMBSGREASEORLIQUIDS/PEN
the bag, clean the upper part of the inside of the bag and remove any residue from
the Sealing Bar (6) before resealing.
s-AKESURETHEBAGISNOTPUNCTUREDANDTHUSDIDNOTMAINTAINTHEVACUUM0ROTECT
any pointed edges of the contents in the bag using paper napkins.
MAGIC VAC
®
does not
seal containers.
s 5SINGTHE Canister Tube (16), connect the canister lid (or the Lid Attachment if
necessary) and the ACCESSORY PORT (4) on the machine.
s,EAVEADEQUATESPACEATLEASTCMBETWEENTHECONTENTSANDTHETOPOFTHEJAR
or canister.
s-AKESURETHATTHERIMOFTHEJARORCANISTERANDUNIVERSALLIDARENOTDAMAGEDIN
the sealing zone. Clean the rim and the lid with a damp cloth and reseal.
s-AKESURETHEGASKETONTHECANISTERLIDORUNIVERSALLIDISPLACEDINTHECORRECT
position and not damaged.
MAGIC VAC
®
Executive
canisters or Universal
MAGIC VAC
®
Lids do
not maintain the seal
s-AKESURETHEKNOBONTHECANISTERLIDISSETTO“VACUUM” before vacuum-packing
and that it is set to “CLOSED” after it is complete.
s#HECKTHATTHEO-Ring under the knob on the canister lid or universal lid is correctly
positioned.
s-AKESSURETHATTHERIMOFTHEJARORCANISTERANDUNIVERSALLIDARENOTDAMAGEDIN
the sealing zone. Clean the rim and the lid with a damp cloth and reseal.
s-AKESURETHEGASKETONTHECANISTERLIDORUNIVERSALLIDISPLACEDINTHECORRECT
position and not damaged.
s-AKESURETHECONNECTIONTUBEISCORRECTLYCONNECTEDTOBOTHTHECANISTERKNOBAS
well as the ACCESSORY PORT (4) on the machine.
The marinating cycle
does not start correctly
s-AKESURETHEKNOBONTHELIDOFTHE3QUAREMAGIC VAC
®
Executive Canister (cod.
ACO1073) is set to “OPEN - (M)” and that the Handles (1) are attached.
s#HECKTHATTHEO-Ring under the knob on the canister lid or universal lid is correctly
positioned.
s-AKESSURETHATTHERIMOFTHEJARORCANISTERANDUNIVERSALLIDARENOTDAMAGEDIN
the sealing zone. Clean the rim and the lid with a damp cloth and reseal.
s-AKESURETHECONNECTIONTUBEISCORRECTLYCONNECTEDTOBOTHTHECANISTERKNOBAS
well as the ACCESSORY PORT (4) on the machine.
s-AKESURETHEGASKETONTHECANISTERLIDORUNIVERSALLIDISPLACEDINTHECORRECT
position and not damaged.
s,IGHTLYPRESSTHECANISTERLIDDOWNWHEN THEFIRSTVACUUMPHASE STARTSUNTILTHE
lights on the Progress Display (2C) are regularly lit.
40