EasyManua.ls Logo

Makita DCS500 - User Manual

Makita DCS500
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Instruction Manual
Original Instruction Manual
Important:
Read this instruction manual carefully before putting the chain saw into operation and strictly observe the
safety regulations!
Keep this instruction manual!
DCS460
DCS461
DCS500
DCS501

Table of Contents

Questions and Answers

  • K
    kelleyveronicaJul 26, 2025
    What to do if my Makita DCS500 engine does not start?
    • C
      christopherrobbinsJul 26, 2025
      If your Makita Chainsaw engine is not starting or starts with difficulty, it could be due to a malfunction in the fuel supply, compression system, or a mechanical issue. Check for an ignition spark and ensure the fuel tank is full. Inspect the wiring for faults or short circuits, and verify the condition of the spark plug. Make sure the combination switch is not in the Choke position. Also, check for carburetor defects, suction head cleanliness, fuel line integrity, and cylinder base packing ring integrity.
  • S
    Sarah BrownJul 31, 2025
    Why does my Makita DCS500 Chainsaw have insufficient power?
    • B
      Brian BrooksJul 31, 2025
      Insufficient power in your Makita Chainsaw may be due to a dirty air filter, incorrect carburetor adjustment, a clogged muffler, a blocked exhaust channel in the cylinder, or a clogged spark arrester screen. To resolve this, clean or replace the air filter, adjust the carburetor, and clear any blockages in the muffler, exhaust channel, and spark arrester screen.
  • B
    beth36Aug 5, 2025
    What to do if Makita DCS500 Chainsaw starts, but dies immediately?
    • T
      Tiffany PhelpsAug 5, 2025
      If your Makita Chainsaw starts but dies immediately, the issue might be an incorrect idling adjustment, or a dirty suction head or carburetor. Try adjusting the idling and cleaning the suction head or carburetor.
  • D
    Diane MitchellAug 10, 2025
    How to fix no chain lubrication on Makita Chainsaw?
    • B
      bhodgesAug 10, 2025
      If your Makita Chainsaw has no chain lubrication, it could be due to an empty oil tank, a dirty oil guide groove, or an incorrectly adjusted oil-pump adjusting screw. Refill the oil tank, clean the oil guide groove, and adjust the oil-pump adjusting screw.
  • A
    Amanda NguyenAug 15, 2025
    Why is my Makita DCS500 Chainsaw having warm start difficulties?
    • S
      Steven BrayAug 15, 2025
      If your Makita Chainsaw is hard to start when warm, the carburetor adjustment might be wrong. You should adjust the carburetor.
  • M
    Matthew WatkinsAug 20, 2025
    How to check the chain brake on a Makita DCS500 Chainsaw if the chain does not run?
    • C
      Clifford HansenAug 21, 2025
      If the chain on your Makita Chainsaw does not run, the chain brake may be actuated. Check the chain brake.

Summary

SAFETY PRECAUTIONS

General Precautions

General safety guidelines for operating the chainsaw.

Protective Equipment

Details on essential personal protective equipment for chainsaw operation.

Fuels; Refuelling

Instructions and precautions for handling fuel and refueling.

Putting Into Operation

Steps and safety checks before starting the chainsaw.

Kickback

Explains kickback and how to prevent it.

Working Behavior;Method of Working

Safe practices and techniques for operating the chainsaw.

Maintenance

Procedures for routine maintenance of the chainsaw.

PUTTING INTO OPERATION

Mounting the Guide Bar and Saw Chain

Step-by-step guide for attaching the guide bar and chain.

Tightening the Saw Chain

Checking the Chain Tension

Retightening the Saw Chain

Chain Brake

Fuel

Fuel Mixture

Refuelling

Chain Oil

Lubricating the Chain

Checking the Chain Lubrication

Adjusting the Chain Lubrication

Starting the Engine

Cold Starting

Warm Starting

Checking the Chain Brake

Adjusting the Carburetor (only for EU-countries)

Adjusting the Carburetor (only for not EU-countries)

MAINTENANCE

Sharpening the Saw Chain

Replacing the Saw Chain

Cleaning the Air Filter

Replacing the Spark Plug

Replacing the Starter Cable;Replacing the Return Spring Pack;Replacing the Starter Spring

Instructions for Periodic Maintenance

Service, Spare Parts and Guarantee

Maintenance and Repair

Spare Parts

Trouble Shooting

Makita DCS500 Specifications

General IconGeneral
Power SourcePetrol
TypeGas Chainsaw
Power Rating2.8 kW
Chain Pitch0.325 inches
Fuel tank capacity0.47 L
Chain oil tank capacity0.27 L
Chain gauge0.058 inches

Related product manuals