Makita DFT024F User Manual

2 ENGLISH
SPECIFICATIONS
Model: DFT024F DFT025F DFT060F
Fastening torque Hard joint 0.5 - 2 N•m 1.5 - 6.5 N•m
Soft joint 0.5 - 2 N•m 1.5 - 6.5 N•m
No load speed (RPM) 260 - 1,600 min
-1
100 - 1,300 min
-1
Dimensions (L x W x H) with BL1815N battery 161 mm x 75 mm x 242 mm
with BL1860B battery 161 mm x 75 mm x 258 mm
Rated voltage D.C. 18 V
Net weight 1.2 - 1.5 kg
• Due to our continuing program of research and development, the specications herein are subject to change without notice.
• Specications may di󰀨er from country to country.
• The weight may di󰀨er depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
Charger DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
DC18SH
• Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or re.
Symbols
The followings show the symbols which may be used
for the equipment. Be sure that you understand their
meaning before use.
Read instruction manual.
Ni-MH
Li-ion
Only for EU countries
Do not dispose of electric equipment or
battery pack together with household waste
material!
In observance of the European Directives,
on Waste Electric and Electronic
Equipment and Batteries and Accumulators
and Waste Batteries and Accumulators
and their implementation in accordance
with national laws, electric equipment and
batteries and battery pack(s) that have
reached the end of their life must be col-
lected separately and returned to an envi-
ronmentally compatible recycling facility.
Intended use
The tool is intended for screw driving in wood, metal
and plastic.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-2:
Model DFT024F
Sound pressure level (L
pA
) : 70 dB(A) or less
Uncertainty (K) : 3 dB(A)
Model DFT025F
Sound pressure level (L
pA
) : 70 dB(A) or less
Uncertainty (K) : 3 dB(A)
Model DFT060F
Sound pressure level (L
pA
) : 70 dB(A) or less
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
NOTE:
The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared noise emission value(s) may
also be used in a preliminary assessment of exposure.
WARNING: Wear ear protection.
WARNING: The noise emission during actual
use of the power tool can di󰀨er from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING: Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
o󰀨 and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-2:
Model DFT024F
Work mode: screwdriving without impact
Vibration emission (a
h
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2
Model DFT025F
Work mode: screwdriving without impact
Vibration emission (a
h
) : 2.5 m/s
2
or less
Uncertainty (K) : 1.5 m/s
2

Makita DFT024F Specifications

General

Brand	Makita
Model	DFT024F
Category	Power Screwdriver
Language	English