Makita DUB361Z User Manual

7 ENGLISH
Overheat protection for battery
Whenthebatteryisoverheated,thetoolstopsauto-
maticallywithoutanyindication.Thetooldoesnotstart
evenifpressingtheswitchbutton.Inthissituation,let
thebatterycoolbeforeturningthetoolonagain.
NOTE:Thebatteryoverheatprotectionworksonly
withabatterycartridgewithastarmarking.
►Fig.2: 1.Starmarking
Overdischarge protection
►Fig.3: 1. Battery indicator
Whentheremainingbatterycapacitygetslow,the
batteryindicatorblinksontheapplicablebatteryside.
Byfurtheruse,thetoolstopsandthebatteryindicator
lightsupabout10seconds.Inthissituation,chargethe
batterycartridge.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
►Fig.4: 1. Indicator lamps 2.Checkbutton
Pressthecheckbuttononthebatterycartridgetoindi-
catetheremainingbatterycapacity.Theindicatorlamps
lightupforfewseconds.
Indicator lamps Remaining
capacity
Lighted Off Blinking
75% to 100%
50% to 75%
25% to 50%
0% to 25%
Charge the
battery.
Thebattery
may have
malfunctioned.
NOTE:Dependingontheconditionsofuseandthe
ambienttemperature,theindicationmaydifferslightly
fromtheactualcapacity.
Switch action
►Fig.5: 1.HIGH/LOWbutton2.OFFbutton
Tostartthetool,simplypressthe"HIGH/LOW"button.
Toswitchoff,pressthe"OFF"button.Tochangethe
toolspeed,pressthe"HIGH/LOW"button.Therst
pressonthisbuttonisforhighspeedandthesecond
pressforlowspeedandtheneachpressonthisbutton
repeats the high/low speed cycle alternatively.
ASSEMBLY
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforecarrying
out any work on the tool.
Installing or removing the long
nozzle
►Fig.6: 1. Hook 2. Button 3. Long nozzle
Toinstallthelongnozzle,pushinontothebloweroutlet
ofthetoolalltheway.
►Fig.7: 1. Button
Toremovethelongnozzle,pressitsbothbuttonsand
withthebuttonsbeingpressedpullitout.
Installing the shoulder strap
►Fig.8: 1. Hanger
Pullthehangeroutofthetool.
Hooktheshoulderstrapontothehangerofthetool.
Beforeuse,adjustthelengthofstrapsothatitiseasy
to work with it.
OPERATION
Blowing
►Fig.9
Holdtheblowerrmlywithahandandperformthe
blowingoperationbymovingitaroundslowly.
Whenblowingaroundabuilding,abigstoneoravehi-
cle,directthenozzleawayfromthem.
Whenperforminganoperationincorner,startfromthe
corner and then move to wide area.
MAINTENANCE
CAUTION:
• Alwaysbesurethatthetoolisswitchedoffand
thebatterycartridgeisremovedbeforeattempt-
ingtoperforminspectionormaintenance.
• Neverusegasoline,benzine,thinner,alcohol
orthelike.Discoloration,deformationorcracks
may result.
Cleaning
►Fig.10
Fromtimetotime,wipeofftheoutsideofthetoolusing
a cloth dampened in soapy water.

Makita DUB361Z Specifications

General

Brand	Makita
Model	DUB361Z
Category	Blower
Language	English