Makita DUC306Z User Manual (English)

Questions and Answers:

C
Christine DiazSep 2, 2025
Why my Makita DUC306Z Chainsaw does not reach maximum RPM?
- C
  Cole SantiagoSep 2, 2025
  If your Makita Chainsaw does not reach maximum RPM, the battery cartridge may be improperly installed; ensure it is correctly installed as described in the manual. Another cause could be dropping battery power, requiring you to recharge or replace the battery cartridge. If these steps do not solve the issue, the drive system may not be working correctly, and you should seek repair from an authorized service center.
D
dianecummingsSep 1, 2025
Why does the motor of my Makita Chainsaw stop after a little use?
- G
  garrisonsarahSep 1, 2025
  If your Makita Chainsaw motor stops running after a short period, the battery charge level is likely low. Recharge the battery cartridges, and if recharging doesn't help, consider replacing the battery cartridge.
M
marshcarolynAug 30, 2025
What to do if Makita Chainsaw has abnormal vibration?
- M
  Mitchell ShafferAug 30, 2025
  If your Makita Chainsaw is vibrating abnormally, immediately stop the machine. This could be due to a loose guide bar or saw chain, so adjust the tension.
J
Jennifer FrazierAug 29, 2025
Why does my Makita DUC306Z Chainsaw motor stop running quickly?
- S
  shannon24Aug 29, 2025
  If the motor of your Makita Chainsaw stops running after a short time, it's likely that the battery's charge level is low. Try recharging the battery cartridges. If recharging doesn't solve the issue, consider replacing the battery cartridge.
S
sellisonAug 27, 2025
What to do if there is no oil on the chain of Makita DUC306Z?
- K
  Kathleen JuarezAug 27, 2025
  If there's no oil on the chain of your Makita Chainsaw, the oil tank might be empty, so fill it up. Another possibility is a dirty oil guide groove, which you should clean. Also, check and adjust the oil delivery with the adjusting screw if the oil delivery is poor.
K
kimberly78Aug 27, 2025
Why the saw chain cannot be installed on my Makita DUC306Z Chainsaw?
- M
  Monica SimpsonAug 27, 2025
  If the saw chain cannot be installed on your Makita Chainsaw, the combination of saw chain and sprocket is not correct. Use the correct combination of saw chain and sprocket by referring to the section for specifications.
K
Keith EstradaAug 25, 2025
What to do if the saw chain does not run on my Makita Chainsaw?
- K
  Kristen MezaAug 26, 2025
  If the saw chain of your Makita Chainsaw does not run, it is likely because the chain brake is activated. Release the chain brake to allow the chain to run.
J
Jennifer GonzalezAug 23, 2025
What to do if there is no oil on the chain of my Makita Chainsaw?
- D
  David RamosAug 23, 2025
  If you notice no oil on the chain of your Makita Chainsaw, the oil tank might be empty, so refill it. Another possible reason is a dirty oil guide groove, which requires cleaning. You may also need to adjust the amount of oil delivery with the adjusting screw if the oil delivery is poor.

Makita DUC306Z Specifications

General

Type	Cordless Chainsaw
Power Source	Battery
Chain Speed	20 m/s
Chain Pitch	3/8"
Oil Tank Capacity	0.2 L
Vibration Level	2.5 m/s²
Battery Type	Lithium-ion
Bar Length	30 cm
Chain Gauge	1.3 mm
Weight	3.4 kg