To Next Page
L
lamblindaSep 23, 2025
How to fix mamibot FLOMO I Error FF:02?
- CChristopher MillerSep 23, 2025
Error FF:02 on your mamibot Ultrasonic Jewelry Cleaner indicates over current in Charging. Replace the Adapter.
How to fix mamibot FLOMO I Error FF:02?
Error FF:02 on your mamibot Ultrasonic Jewelry Cleaner indicates over current in Charging. Replace the Adapter.
Why is my mamibot FLOMO I Clean Water Tank leaking?
If the Clean Water Tank of your mamibot Ultrasonic Jewelry Cleaner is leaking, it might be overfilled. Pour out some water until the water level is below the snuffle valve. Also, make sure the Clean Water Tank is properly installed and the cap is screwed on tightly.
What to do if mamibot FLOMO I Ultrasonic Jewelry Cleaner Flomo doesn’t work in Self-Cleaning Mode?
If your mamibot Ultrasonic Jewelry Cleaner Flomo isn't working in Self-Cleaning Mode, make sure it’s properly connected to the power supply. Also, check if the Dirty Water Tank is full and empty it if necessary. Finally, ensure there is enough water in the Clean Water Tank and refill it if needed.
How to fix Error FF:10 on mamibot FLOMO I?
Error FF:10 on your mamibot Ultrasonic Jewelry Cleaner indicates a Roller Brush Overcurrent. Check and clean the Roller Brush.
How to fix mamibot Ultrasonic Jewelry Cleaner Error FF:05?
Error FF:05 on your mamibot Ultrasonic Jewelry Cleaner means the battery voltage is too low. Check the connection or replace the Battery Pack.
How to fix mamibot Ultrasonic Jewelry Cleaner Error FF:01?
Error FF:01 on your mamibot Ultrasonic Jewelry Cleaner indicates over voltage in Charging. Replace the Adapter.
Why can't I charge my mamibot FLOMO I Flomo?
If your mamibot Ultrasonic Jewelry Cleaner Flomo isn't charging, the power supply may not be well connected. Check the connection of the power supply. Also, ensure Flomo is properly placed on the charging station.
Why are there water drops at the air outlet of my mamibot FLOMO I Ultrasonic Jewelry Cleaner Flomo?
If you notice water drops at the air outlet of your mamibot Ultrasonic Jewelry Cleaner Flomo, it could be due to several reasons. The HEPA filter might not be installed. Ensure the HEPA filter is installed. Also, avoid tilting Flomo excessively and promptly empty the Dirty Water Tank if Flomo vacuums foam liquid.
How to fix mamibot Ultrasonic Jewelry Cleaner Error FF:06?
Error FF:06 on your mamibot Ultrasonic Jewelry Cleaner indicates an over voltage-differential in the Battery. Replace the Battery Pack.
How to fix mamibot FLOMO I Ultrasonic Jewelry Cleaner Error FF:07?
Error FF:07 on your mamibot Ultrasonic Jewelry Cleaner indicates that the discharging temperature is too high. Use the Cleaner when the temperature gets normal.
Lists all components included with the floor cleaner.
Illustrates and labels the various parts of the Flomo from the front.
Illustrates and labels the various parts of the Flomo from the back.
Shows a diagram of the clean water tank with its components.
Details the components of the brush base, including the roller brush lock and sensor.
Illustrates the charging station and its drying tray.
Step-by-step instructions for assembling the Mamibot Flomo I unit.
Instructions on how to remove, fill, and reinsert the clean water tank.
Guides on how to charge the Flomo unit using the charging station or battery pack.
Instructions on how to prepare and use the Flomo for cleaning floors.
Steps to remove and clean the roller brush.
Instructions for cleaning the dirty water tank, HEPA filter, and strainer.
Guidance on cleaning the charging station and drying tray.
Recommendations for storing the Flomo and its accessories.
Lists error codes, their possible reasons, and solutions for the Flomo I.
Information on how to dispose of the product responsibly.
General| Brand | mamibot |
|---|---|
| Model | FLOMO I |
| Category | Ultrasonic Jewelry Cleaner |
| Language | English |
