To Next PageTo Next PageCan I install MantelMount TV Mount on brick or stone?
If the wall covering is made of brick or stone, it’s possible to install MantelMount by replacing the Lag Bolts with concrete anchors of the same size if the brick/stone is both firm and at least 1.5" deep.
How to install MantelMount TV Mount on a single stud?
It’s OK to mount the Wall Plates of MantelMount TV Mount to a single stud by driving two Lag Bolts through the center of the Wall Plates and into the center stud.
What to do if my MantelMount TV Mount won’t stay in place?
If your MantelMount TV Mount won’t remain stationary, you may need to adjust the Lifting Force. See Step 5.1 for instructions on how to make these adjustments.
Why is my MantelMount TV Mount hard to lift up?
If your MantelMount TV Mount is difficult to lift up, slightly tighten it when it’s in the UP position. Review Step 5.1 to make minor clockwise adjustments to the Lifting Force, then try lifting up the TV again.
How to make MantelMount TV Mount easier to pull down?
If your MantelMount TV Mount is difficult to pull down, use the MantelMount Three-Step Pull-Down Technique.
Why is my MantelMount TV Mount level down but not up?
If your MantelMount TV Mount is level in the DOWN position, but unleveled in the UP position, Post-Leveling Adjustments haven’t been made. Refer to Step 5.6 and make adjustments.
How to lower my MantelMount TV Mount more than it does now?
If your MantelMount TV Mount is not lowering the full vertical travel listed in the specifications, and you want it to drop below the lowest Bottom Stop Position, remove the Bottom Stop Screws on each side (see Step 5.3); the TV will travel even lower.
Why is my MantelMount TV Mount level up but not down?
If your MantelMount TV Mount is level in the UP position, but unleveled in the DOWN position, the Bottom Stops aren’t evenly set. Follow the instructions in Step 5.3.
What to do if Lifting Arm of MantelMount TV Mount won’t pull down?
If the Lifting Arm won’t pull down in order to insert the Safety Bolt, first, make sure the TV Brace is attached to the Lifting Arm (see Step 3.7) and follow the described technique for pulling down the Lifting Arm.
Why is my MantelMount TV Mount not level?
If your MantelMount TV Mount is not level in the UP and/or DOWN positions, the mantel, ceiling or floor may not be level. Adjust until visibly satisfactory.
The MantelMount MM440 is a standard pull-down TV mount designed to bring your television down from above a fireplace or other elevated position to an optimal viewing height. This device is engineered for ease of use and safety, allowing for a comfortable and dynamic viewing experience in various room setups.
The primary function of the MM440 is to provide a smooth, controlled vertical and horizontal movement for your television. It allows users to pull the TV down from a raised position, typically above a mantel, to eye level, and then push it back up when not in use. This movement is facilitated by a gas spring mechanism that assists in lifting and lowering the TV, making the operation feel lightweight and effortless. The mount also offers swivel capabilities, allowing the TV to be angled left or right for optimal viewing from different seating arrangements in a room. A key safety feature is the patented Heat-Sensing Handle, which turns red if the temperature above the fireplace exceeds a safe threshold (110° F), alerting users to either raise the TV or turn off the fireplace to prevent potential damage.
The MM440 is designed for intuitive operation, with several features enhancing its usability:
The MM440 is built for durability and requires minimal ongoing maintenance. However, certain aspects are designed for user-friendliness in case of adjustments or future needs:
In summary, the MantelMount MM440 is a robust and user-centric TV mount that prioritizes safety, flexibility, and a premium viewing experience, making it an excellent solution for integrating a television seamlessly into spaces with elevated mounting positions.
General| Mount Type | Full Motion |
|---|---|
| Weight Capacity | 125 lbs |
| Construction | Heavy-duty steel |
| Finish | Powder-coated |
| Material | Steel |
| Color | Black |
| VESA Compatibility | 200x200mm to 600x400mm |
| TV Size Range | 45" - 80" |
