Marantz CD50 - Page 8

PROGRAMMING
It is possible to program in two ways:
ADD-IN PROGRAMMING: You store in the players memory the tracks
which are to be played and their order. Up to 20 track numbers can be stored
in this way.
TAKE-OUT PROGRAMMING: You erase the track numbers you do not want
to hear. Nowyou can store as many numbers as there are tracks on the disc.
NOTE!
— Index numbers cannot be stored.
— Once you are programming in one of the two ways, you can no longer
switch to the other way.
— A programme can be stored either before or during play.
— Ifyou wish to compile your programme before starting play, first load the
disc but do not close the tray yet!
~ When storing track numbers, make sure that no more than 7 seconds
elapse between pressing keys, or the display will again show the number
of tracks and the playing time of the disc.
— If you exeed the maximum of 20 tracks or if you select a number which
does not exist then Error appears.
ADD-IN PROGRAMMING
@ Key in the first required number or press 1 or <4 until the number
appears under TRACK.
e@ Press MEMO.
— The number is now stored in the player's memory.
— Store the other tracks required in the same way.
— Each time you store a track, the number of tracks and the playing time
of your programme will be shown under STEP and MIN and SEC for a
few seconds.
— The track number indicator always shows which numbers have been
stored.
NOTE!
If you press PROGRAM MODE during programming, the information under
STEP and MIN and SEC remains visible. However, all other information will
disappear. You can call this information up again by pressing PROGRAM
MODE twice.
TAKE-OUT PROGRAMMING
@ Key in the first number you wish to omit or press b>}! or <d until the
number appears under TRACK.
@ Press CANCEL.
— The number disappears from the track number indicator; it has now been
erased.
@ Erase the other tracks you do not wish to hear in the same way.
— Each time you erase a track, the remaining tracks and their playing time
will be shown under STEP and MIN and SEC for a few seconds..
— The track number indicator always shows which tracks remain for
inclusion in your programme.
— The numbers displayed on the track number indicator after the unwanted
numbers have been erased, are included in the programme in the order
in which they appear on the disc.
NOTE!
If you press PROGRAM MODE during programming, the information under
STEP and MIN and SEC remains visible. However, all other information will
disappear. You can call this information up again by pressing PROGRAM
MODE twice.
STORING TRACK NUMBERS USING AMS
@ Press AMS (on the remote control) before or during play.
— AMS lights up.
~ If the tray is open, it will now close.
— The first 20 seconds of each track are played in turn.
@ Now you can compile your programme in either the add-in or the take-out
way:
Add-in
@ Press MEMO at each track you wish to include in the programme.
— The number appears on the track number indicator; it has now been
stored.
— The playerimmediately starts to play the first 20 seconds of the next track.
Take-out
@ Press CANCEL at each track you do not wish to include in the
programme.
~ The number disappears from the track number indicator; it has now been
erased.
— The playerimmediately starts to play the first 20 seconds of the next track.
REVIEWING A PROGRAMME
@ Press RECALL.
— All track numbers appear on the display in the order in which they were
stored.
— If Error appears, the memory is empty and nothing has been stored.
You can review a programme prior to, during or after programmed play.
PROGRAMMED PLAY
@ Press PLAY-REPLAY (>).
— lf the tray was open, it will now close.
— Play begins with the first number of the programme.
All keys can be used during programmed play.
Searching for a passage is only possible in the track which is being played.
ERASING A PROGRAMME
e@ Press STOP/CM twice, or if the disc has already stopped, just once.
e@ You can also press OPEN straight away.
— The programme has now been erased.
ERASING A TRACK FROM A PROGRAMME
e@ Press RECALL before or after programmed play.
— All track numbers appear on the display in the order in which they were
stored.
@ Press CANCEL as soon as the number which you want to erase appears.
— The erased number will disappear from the display and from the track
number indicator.