Dolby Digital EX
®
/DTS ES
®
Surround Receiver
SR5500
Product Accessories
30 7
The SR5500 is an embarrassment of riches. Each “current feedback” amplifier produces 90 Watts RMS, sufficient for all but the largest rooms
or most inefficient speakers. The 32-Bit microprocessor decodes all Dolby, DTS surround sound formats, and SRS’ Circle Surround II. Consider
the SR5500’s multi-source/multi-room capabilities. Look no further than the front panel inputs to conveniently plug in a camcorder, portable
DVD player and/or game console. You’ll appreciate the SR5500’s enhanced video conversion capabilities as you watch a full complement of
sources through your monitor’s high quality component video input. Want a customized system? The RS232 port allows total control for
external sources. The on-screen display quickly guides you through setup. The SR5500’s “Lip Sync” circuit assures you that sounds reach your
ears at exactly the moment your eyes say they should. And its all covered by a three-year warranty.
• 90 Watts (into 8 ohms) x 7 ch Amps
• Dolby Digital EX
®
, Pro Logic IIx
®
(Movie/Music/Game),
• DTS 96/24, ES
®
(Discrete 6.1/Matrix
6.1), Neo:6 (Cinema/Music)
• SRS Circle Surround II
®
• All Discrete “Current Feedback”
Amplifier Stages
• 32-Bit DSP
• 192kHz/24-Bit D/A Converters for
all Channels
• Dolby Headphone
• Video Up-conversion: Composite/
S-Video to Component
• Multi-room/Multi-source Capability
with Discrete Commands
• Multi Speaker “B” Output
• Lip Sync Control
• On Screen Display
• Pure Direct Mode
• Video Off Mode
• Variable Cross-over
• Assignable HD Compatible
Component Video Switching
(2 in/1 out)
• 4 Assignable Digital Inputs
(2 optical/2 coaxial)
• 2 Digital Outputs
(1 optical/1 coaxial)
• Front Panel A/V Inputs
• 50 Station Presets
• Manual Station Naming
• RS232C Terminal for System Control
• 1 Switched and 1 Un-switched AC
Convenience Outlets
• D-BUS (RC-5 In/Out) Remote
Connection
• Includes Pre-programmed
System Remote
PD6140D ACCESSORIES
PD5050D/PD4250D/PD4230V ACCESSORIES
WB6200 Flush Wall Mount Bracket for
PD6140D
AS6140 Accessory Stand for PD6140D
WB6100 Tilting Wall Mount
Bracket for PD6140D
VQ2400 HD COMPATIBLE VIDEO UP CONVERTER WITH TBC
AS5400
Accessory Stand for
PD5050V/PD4250V/PD4230V
WB5400
Flush Wall Mount Bracket for
PD5050V/PD4250v/PD4230v
WB4000
Tilting Wall Mount Bracket for
PD5050V/PD4250V/PD4230V
This groundbreaking product was designed to make every home theater a lot less complicated. To use, simply connect the Composite
Video, S-Video, and/or Component Video outputs from your existing receiver/preamp to the corresponding inputs on the VQ2400 and
then connect one cable from the Component Video output on the VQ2400 to your display device. Power it with the included 12 volt
power supply and the VQ2400 will seamlessly “upconvert” all the signals to component level, eliminating the need to run multiple
cables from your equipment rack to the video display. From then on, you will never need to switch inputs on your display device
again. It’s that easy and it is compatible with virtually any Receiver/Pre Amp available, regardless of brand. The VQ2400 also
incorporates Time Based Correction for compatibility with fixed pixel devices such as plasma displays and DLP projectors.
VP-10S1/VP-12S4 ACCESSORIES
AJ8300 RS-232 CABLE FOR MV8300
EXT10
Extension Rod for MOUNT 10 Ceiling Bracket
MOUNT12
Ceiling Mount Bracket for VP-12S4
MOUNT10
Ceiling Mount Bracket for VP-10S1
Compatible
To Next Page
Loading...
