Marantz SC-80 User Manual

OPERATION
PROCEDURES
TO
PLAY
AN
ANALOG
RECORD
4.
Set
the
INPUT
SELECTOR
switch
to
PHONO.
2.
Setthe
CARTRIDGE
switch
on
the
rear
panel
according
to
the
type
of
the
Cartridge
used
with
your
turntable
(MC-LOW,
MC-HIGH,
or
MM).
The
MC-LOW
position
is
to
be
used
incase
the
load
impedance
of
your
Cartridge
is
below
100
ohms.
.
Play
an
analog
record
on
the
tumtable.
4.
Adjust
the
volume
with
the
VOLUME
control
and
adjust
the
tone
with
the
BASS
and
TREBLE
controls.
o
NOTES:
>
?
;
@
Setthe
VOLUME
control
to
the
minimum
position
before
placing
the
stylus
on
the
record
or
before
replacing
the
cartridge.
@
Do
not
apply
shock
or.
vibration
to
the
turntable
during
play,
as
this
may
cause
the
stylus
to
jump
and
the
analog
record
to
be
damaged.
@
Ifthe
turntable
is
installed
too
close
to
the
speakers,
the
volume
may
not
be
able
to
be
increased
to
a
high
level
due
to
howling.
~
@
Do
not
switch
the
power
OFF
while
the
stylus
is
on
the.
record
surface.
©
Set
the
VOLUME
control
to
the
minimum
position
before
switching
the
CARTRIDGE
switch.
TO
LISTEN
TO
FM/AM
BROADCASTS
4.
Set
the
INPUT
SELECTOR
switch
to
TUNER.
2.
Tune
in
the
desired
station
on
the
tuner.
3.
Adjust
the
volume
with
the
VOLUME
control
and
adjust
the
tone
with
the
BASS
and
TREBLE
controls.
TO
PLAY
A
COMPACT
DISC
4.
Set
the
INPUT
SELECTOR
switch
to
CD.
.
2.
Play
a
CD
on
the-CD.
player.
3.
Adjust
the
volume
with
the
VOLUME
control
and
adjust
the
tone
with
the
BASS
and
TREBLE
controls.
TO
PLAY
A
COMPONENT
CONNECTED
TO
AUX
1
JACKS
The
component
connected
to
the
AUX
1
jacks
on
the
rear
panel
can
be
played
as
follows...
4.
Set
the
INPUT
SELECTOR
switch
to
AUX
1.
2.
Play
the
component
connected
to
the
AUX
1
jacks.
3.
Adjust
the
volume
with
the
VOLUME
control
and
adjust
the
tone
with
the
BASS
and
TREBLE
controls.
TAPE DECK OPERATIONS
TAPE PLAYBACK 7
1. Press the TAPE 1 MONITOR switch. The indicator above the
switch lights up.
2. ey a prerecorded tape on the tape deck connected to the TAPE. 1
jacks. a ee Eeue ne ee
3. Adjust the volume with the VOLUME control.
4. Adjust the tone with the BASS and TREBLE controls.
NOTES: —
@ When the tape is not to be played, press the TAPE 1 MONITOR
switch again (so that the TAPE 1 indicator goes out).
@ The tape can be played. regardless of the setting of the INPUT
SELECTOR. E :
TAPE RECORDING
The playback sound of a program source component, such as the
turntable, tuner, or CD player; can be recorded on tape as follows.
1. Set the REC SELECTOR switch to the TUNER, CD, or PHONO
position according to the program source to be recorded.
2. When the program source to be recorded is one of the sources
selected with the INPUT SELECTOR, such as AUX 1 and AUX 2,
set the REC SELECTOR switch to SOURCE.
3. Start playing the program source.
4. Operate the tape deck to start recording on tape.
TAPE MONITORING
When a three-head tape deck is connected to the TAPE 1 jacks, the
sound recorded:on tape can be. monitored through the speakers by
pressing the TAPE 1 MONITOR switch. In this case, the tape deck
must be connected to this unit via both recording (OUT) and playback
(IN) connection-cords.
NOTE: ; panes:
When the tape deck is a two-head system, the recorded sound cannot
be monitored even when the TAPE 1 MONITOR switch is pressed. In
this case, however, the sound of the program source being recorded
can be monitored.
DUBBING OF PRERECORDED TAPE USING REC
SELECTOR SWITCH
For dubbing from tape to tape(s), set the REC SELECTOR switch to
TAPE COPY 2 — 1.
Tapes can be copied regardless of the setting of the INPUT
SELECTOR switch.
NOTES: ; ,
@ To monitor the recorded sound, press the TAPE 1 or TAPE 2
MONITOR switch.
@ The program source selected with the INPUT SELECTOR switch
can be played during dubbing.
@ No signal is output at the TAPE 1 and DAT/TAPE 2 OUT jacks
when the REC SELECTOR switch is set to OFF. There is no need to
output a signal at the TAPE 1 and DAT/TAPE 2 jacks unless when
recording it on tape(s). Therefore, it is recommended to set the REC
SELECTOR switch usually to OFF so that the signal path inside the
~ unit can be shortened and crosstalk etc., can be reduced.
@ With the SOURCE position, the signal selected with the INPUT
SELECTOR can be recorded on tape(s).
® The tape dubbing with the TAPE COPY 2 — 1 position and the tape
recording with the TUNER, CD, and PHONO positions can be
performed regardless of the INPUT SELECTOR setting.

Marantz SC-80 Specifications

General

Brand	Marantz
Model	SC-80
Category	Amplifier
Language	English