Market Forge Industries M24E18A

Questions and Answers

U
uhuntAug 20, 2025
Why does my Market Forge Industries Boiler fail to build up pressure?
- F
  Frederick OsborneAug 20, 2025
  If the Market Forge Industries Boiler fails to build up pressure, first check that the circuit breaker is on. Then, check for voltage at the terminal block. Also, check that the contactors are pulling in; if the coil's continuity is open, replace it. Verify that the current flow isn't broken at the water level control by checking for voltage at L1 and L2; replace if defective. Additionally, ensure that the current flow isn't interrupted at the pressure control or high limit control switches due to maladjustment or defect; readjust to the proper setting or replace if defective. Finally, inspect the heating elements and replace any that are defective based on a continuity check.
N
Nathaniel LiAug 22, 2025
What to do if Market Forge Industries Boiler fails to reach full operating pressure?
- S
  Susan BakerAug 22, 2025
  If your Market Forge Industries Boiler isn't reaching full operating pressure, it could be due to several reasons. Start by replacing the pressure gauge if it reads inaccurately. If the pressure control and high limit control switches are out of adjustment, follow instructions for readjusting, or replace them if defective. Ensure the safety valve is seating properly; clean or replace it if necessary. Also, check if the contactor coils are energizing and closing the circuit to the heating elements; replace either the contactor coils or the complete contactor if found defective.
M
Megan ScottAug 25, 2025
Why does the 15 lbs safety valve on my Market Forge Industries Boiler blow off prematurely?
- S
  schultzjenniferAug 25, 2025
  If the 15 lbs. safety valve on your Market Forge Industries Boiler blows off prematurely, the pressure might be set too high, so readjust it. Another possibility is that the pressure gauge reads incorrectly, in which case you should replace it. Mineral build-up or dirt on the seat of the valve can also cause this issue, so clean it. Lastly, a weak spring valve can be the culprit, requiring you to replace the valve.
A
anitaparkerAug 26, 2025
How to fix contactor chatter in Market Forge Industries Boiler?
- K
  Kim BellAug 26, 2025
  If the contactor chatters in your Market Forge Industries Boiler, first check that the supply voltage matches the coil contactors. If the contactor points are dirty or worn, clean or replace the contactor. A weak coil can also cause this, so replace it with the correct voltage coil.
C
Cindy PattersonAug 28, 2025
What to do if water does not enter Market Forge Industries Boiler?
- N
  Nicole WatsonAug 28, 2025
  If water isn't entering your Market Forge Industries Boiler, ensure the water main is turned on. Check the main fuse or circuit to make sure power is reaching the unit. If the probes are dirty, remove and clean them. If 120V is verified at the solenoid coil, but it fails to open, replace the solenoid.
G
Gregory PerryAug 30, 2025
Why does my Market Forge Industries Boiler shut down and fail to restart?
- J
  Joseph HooverAug 30, 2025
  If the Market Forge Industries Boiler builds up pressure, shuts down, and fails to come back on, the high limit switch might be set too low, or the operating pressure control switch set too high. Follow the instructions for readjusting, or replace if defective.
B
brianrichardsonSep 1, 2025
Why is the cold water condenser not working on my Market Forge Industries Boiler?
- J
  Julie StoutSep 1, 2025
  If the cold water condenser on your Market Forge Industries Boiler isn't functioning, ensure the main water line is turned on. If the thermostat is defective, replace it. Also, tighten the coil nut and check the solenoid coil for continuity; replace it if it's open.
S
swilsonSep 3, 2025
Why does the water level fluctuate in my Market Forge Industries Boiler?
- K
  Kevin MasonSep 3, 2025
  If the water level in the gauge glass of your Market Forge Industries Boiler fluctuates up and down, the top shut off on the water gauge might be closed. Open it.
D
Daniel WilliamsSep 5, 2025
Why does water enter Market Forge Industries Boiler so slowly?
- C
  careydanielleSep 5, 2025
  If water enters the Market Forge Industries boiler very slowly, the strainer screen in the solenoid valve might be dirty. Clean or replace the strainer screen.
C
Colleen DeleonSep 7, 2025
How to fix a leaking air vent on Market Forge Industries Boiler?
- J
  Jeffrey MichaelSep 7, 2025
  If the air vent on your Market Forge Industries Boiler is leaking, replace it.