Mars RG Series - Page 28

Owner’s Manual - RG/RADS Series
28
Air Conditioner
Features
MECHANICAL CONTROL OPERATING INSTRUCTIONS
Cool Mode
Fan Mode
Thermostat
The desired cool setting is selected by rotating the knob to the right to the
appropriate location.
HI COOL
LO COOL
MED COOL
NOTE: If your unit is equipped with a vent handle, keep it closed for maximum
Rotate the knob to the left to select your choice of fan speeds for air circulation.
NOTE: When selecting a fan speed, the compressor will not run. On models with
a vent control, this mode can be used to remove stale air from the room, or to
draw fresh air into the room.Check the section “ Fresh Air Vent Control”.
The thermostat i s used to s et the desired room temperature when the unit is
being operated in the
COOL MODE.
To set the desired room temperature, rotate the thermostat switch to the desired
setting. After the set temperature is achieved the thermostat will automatically
start and stop the compressor in order to maintain the desired set temperature.
Rotate the thermostat selector clockwise for higher cool settings. Higher cool
settings will provide lower room temperature. Rotate the thermostat selector
counter clockwise for lower cool settings. Lower cool settings will provide higher
room temperature.
NOTE:
The controls featured in this manual are representative of many available
The Fresh Air Vent allows the air conditioner to:
1. Recirculate inside air - Vent Closed (See Fig.A)
2. Draw fresh air into the room- Vent Open (see Fig.B)
3. Exchange air from the room and draws fresh air into the room - Vent and Exhaust Open (see Fig.C)
Fresh Air Vent Control (on 15~28.5K models):
Fig. A
(VENT CLOSED)
Fig. B (VENT OPEN)
Fig. C (VENT & EXHAUST OPEN)
TEMPERATURE
min
cool
max
cool
COOLING
1
4
5
6
7
2
3
lo
fan
lo
cool
hi
cool
hi
fan
OFF
TEMPERATURE
MIN
COOL
MAX
COOL
LO
FAN
MED
FAN
MED
COOL
LO
COOL
HI
COOL
HI
FAN
OFF
COOLING
1
2
3
4
5
6
7
Air Conditioner
Features
MECHANICAL CONTROL OPERATING INSTRUCTIONS
Cool Mode
Fan Mode
Thermostat
The desired cool setting is selected by rotating the knob to the right to the
appropriate location.
HI COOL
LO COOL
MED COOL
NOTE: If your unit is equipped with a vent handle, keep it closed for maximum
Rotate the knob to the left to select your choice of fan speeds for air circulation.
NOTE: When selecting a fan speed, the compressor will not run. On models with
a vent control, this mode can be used to remove stale air from the room, or to
draw fresh air into the room.Check the section “ Fresh Air Vent Control”.
The thermostat i s used to s et the desired room temperature when the unit is
being operated in the
COOL MODE.
To set the desired room temperature, rotate the thermostat switch to the desired
setting. After the set temperature is achieved the thermostat will automatically
start and stop the compressor in order to maintain the desired set temperature.
Rotate the thermostat selector clockwise for higher cool settings. Higher cool
settings will provide lower room temperature. Rotate the thermostat selector
counter clockwise for lower cool settings. Lower cool settings will provide higher
room temperature.
NOTE:
The controls featured in this manual are representative of many available
The Fresh Air Vent allows the air conditioner to:
1. Recirculate inside air - Vent Closed (See Fig.A)
2. Draw fresh air into the room- Vent Open (see Fig.B)
3. Exchange air from the room and draws fresh air into the room - Vent and Exhaust Open (see Fig.C)
Fresh Air Vent Control (on 15~28.5K models):
Fig. A
(VENT CLOSED)
Fig. B (VENT OPEN)
Fig. C (VENT & EXHAUST OPEN)
TEMPERATURE
min
cool
max
cool
COOLING
1
4
5
6
7
2
3
lo
fan
lo
cool
hi
cool
hi
fan
OFF
TEMPERATURE
MIN
COOL
MAX
COOL
LO
FAN
MED
FAN
MED
COOL
LO
COOL
HI
COOL
HI
FAN
OFF
COOLING
1
2
3
4
5
6
7