CV620-IP / CV620-NDI RS-232 Command Set
www.marshall-usa.com13 14
Command Set Command Command Packet Comments
Pan-tiltLimitSet
LimitSet
8x 01 06 07 00 0W
0Y 0Y 0Y 0Y 0Z 0Z
0Z 0Z FF
W: 1 UpRight YYYY: Pan Limit
Position 0x0000~0x3A80 ZZZZ: Tilt
Limit Position 0x0000~0x3DE0
W: 0 DownLeft YYYY: Pan Limit
Position 0xFFFF~0xC580 ZZZZ: Tilt
Limit Position 0xFFFF~0xEB60
LimitClear
8x 01 06 07 01 0W
07 0F 0F 0F 07 0F
0F 0F FF
Firmware
Firmware
version
8x 01 02 03 FF
Error Code
Read Error
Code
8x 01 01 01 FF
Clear Error
Code Record
8x 02 02 02 FF
Factory Reset
System Factroy
Reset
8x 01 04 3F 03 00
FF
CAM_Image_Mode
Select CAM
Image Mode
8x 01 04 3F 04 0p
FF
p: 0~6, 6:Custom mode
CAM Prompt
Set Prompt On/
Off
8x 01 04 07 00 0p
FF
p: 2 to 3, 2:Prompt On , 3:Prompt Off
CAM Model ID
Set Camera
model ID
8x 01 04 23 pp qq
rr ss FF
ppqq: Vender ID , rrss:Model ID,
default: SRG-300 (Vender ID =
0xEEEE)
AF Speed
Normal 8x 01 04 56 02 FF
Set anytime AF speed : Normal / Fast
Fast 8x 01 04 56 03 FF
AF Sensitivity - 8x 01 04 58 0p FF p: 1 to 3, 1:High , 2:Middle, 3:Low
CAM_
ImageModeBrightness
Set Brightness
8x 01 04 75 67 pq
FF
pq: 0x00~0x19(* Enabled during
Image Mode = Custom mode )
CAM_
ImageModeContrast
Set Contrast
8x 01 04 75 68 pq
FF
pq: 0x00~0x19(* Enabled during
Image Mode = Custom mode )
CAM_Skin_Tone select red level
8x 01 04 75 06 0p
FF
p: 0~5(* Enabled during Image Mode
= Custom mode )
Black Level Black Level
8x 01 04 75 69 0p
FF
p: 0 to 5, 0:Off, 1:Type 1, 2:Type 2,
3:Type 3, 4:Type 4, 5:Type 5
(* Enabled during Image Mode =
Custom mode )
SYS_Menu
On 8x 01 06 06 02 FF turn on the menu screen
Off 8x 01 06 06 03 FF turn off the menu screen
On/Off 8x 01 06 06 10 FF turn on/off the menu screen
Pan speed table update
command
-
8x 01 06 1A 0p 0q
0r 0s 0u 0v FF
pqrs: 0x0 ~ 0xFFFF , uv: 0x01 ~ 0x64
Tilt speed table update
command
-
8x 01 06 1B 0p 0q
0r 0s 0u 0v FF
pqrs: 0x0 ~ 0xFFFF , uv: 0x01 ~ 0x64
Pan/Tilt speed table to
default
-
8x 01 06 1C 0p 0q
0D 0E 0F FF
pq: 0x18 or 0x64
Pan/tilt speed table size -
8x 01 06 1D 0p 0q
FF
pq: 0x18 or 0x64
Pan/tilt speed table
save
- 8x 01 06 1E FF
Command Set Command Command Packet Comments
CAM_SET_ETHERNET_
DHCP
Ethernet DHCP
Enable/Disable
8x 01 CC 0p FF p: 0~1 , 0: Disable 1: Enable
CAM_HARDWARE_
FACTORY_RESET
System
Hardware
Factory Reset
8x 01 CD 0p FF p: 1, 1: Enable
CAM_MSDC_RESET
MSDC Storage
Reset
8x 01 CE 0p FF p: 1, 1: Enable
Tally Mode -
8x 01 7E 01 0A 01
0p FF
p: 0: (Power LED:Green
Standby:OFF)
5: (Power LED:Red Standby:Red)
- Tally Lamp must be Enabled
6: (Power LED: Green
Standby:Red) - Tally Lamp must be
Enabled
7: (Power LED: OFF
Standby:OFF) - Tally Lamp must be
Enabled
Tally_Lamp
8x 01 7E 01 0A 00
0p FF
p: 2 Enable 3: Disable
VISCA_MF_PTZ_Assist
8x 01 04 38 03 0p
FF
p: 0(OFF) 1(ON)
VISCA_OPTICAL_
ZOOM_LIMIT
8x 01 04 47 0p 0q
FF
pq: 0 ~ 0x13(Ratio : x1 ~ x20)
Power_LoadState
8x 01 04 75 6A 02
FF
Load preset 0 when power on
8x 01 04 75 6A 03
FF
Load Last status when power on
PanTilt_Control_Device
8x 01 7E 03 01 0p
FF
p: 0 Encoder 1: Controller
PanTilt_Preset_Speed
8x 01 7E 03 02 0p
FF
p: 0: [5 deg/sec] 1: [15 deg/sec] 2: [25
deg/sec] 3: [35 deg/sec]
4: [50 deg/sec] 5: [75 deg/sec] 6:
[100 deg/sec] 7: [120 deg/sec]
PTZ Speed Comp
8x 01 7E 03 03 0p
FF
p: 0:OFF 1:ON
VISCA_SET_REBOOT Set Reboot 8x 01 7E 74 FF Set to reboot
To Next Page
Loading...
Need help?
General
