01B01-9
HD Series 2600
Technical Specifications
01
15 - Drawbar
Max static load - all positions - kg (pounds) ........................................... 1179 (2599)
Distance to PTO shaft - retracted position - mm (in).........................254 (10) 356 (14)
Distance to PTO shaft - extended position - mm (in)........................ 356 (14) 406 (16 )
Drawbar face to center of PTO shaft - Minimum - mm (in)................65 (4.3) 108 (4.25)
Drawbar face to center of PTO shaft - Maximum - mm (in)...............265 (10.1) 257 (10.13)
Drawbar side swing from center - mm (in) .............................................. 228 (9.12)
16 - Cab and air conditioning
Features ............................................................. Supported on rubber pads to absorb vibrations, it incorporates acoustic and heat
insulation, access through both doors, all-round visibility, and excellent ergonomic
layout.
Compressor .............................................................................................. Belt driven.
Refrigerant gas ......................................................................................... R-134a - 1,7 kg (3,7 pounds)
Condenser ................................................................................................ Located in front of the water radiator.
Air filter ...................................................................................................... Paper element located on the cab roof.
17 - Wheel Bolt or Nut Torque
Rear: Torque for single and dual tires
Rear - pressed wheels:
Disc to axle hub ................................................ 265 N.m (195 ft.lbs)
Rim to disc ........................................................ 150 N.m (110 ft.lbs)
Rear - PAVT wheels:
Disc to Axle Hub ................................................ 325 N.m (240 ft.lbs)
Clamp nuts ....................................................... 260 N.m (190 ft.lbs)
Front - two-wheel drive axle:
Disc to axle hub .................................................150 N.m (110 ft.lbs)
Rim to disc ........................................................ 150 N.m (110 ft.lbs)
Front - four-wheel drive axle:
Disc to axle hub ................................................ 265 N.m (195 ft.lbs)
Rim to disc ........................................................ 150 N.m (110 ft.lbs)
Front: Torque for single tires
14 - Filling capacities 2650 2660 2670 2680
Engine sump oil-including filter - liter (US gal) 9,0 (2.36) 9,0 (2.36) 9,0 (2.36) 9,0 (2.36)
Cooling system - liter (US gal) ......................... 14,6 (3.86) 14,6 (3.86) 14,6 (3.86) 14,6 (3.86)
Fuel tank
Footstep version - liter (US gal) ........................ 100 (26,5) 100 (26,5) 100 (26,5) 100 (26,5)
Cab version - liter (US gal) ............................... 100 (26.5) 100 (26.5) 100 (26,5) 100 (26,5)
Transmission/hydraulic oil - liter (US gal) ........ 42,0 (11.1) 42,0 (11.1) 45,0 (11.9) 45,0 (11.9)
Rear planetary reducers - each - liter (US pt) .. 2,0 (3,6) 2,0 (3,6) 3,0 (5.4) 3,0 (5.4)
Four-wheel drive front axle differential .............. 4.5 (1.2) 4.5 (1.2) 5.5 (1.45) 5.5 (1.45)
Four-wheel drive front axle planetary - each side - liter (US pt)
.................................................................. 0.7 (1.47) 0.7 (1.47) 1.0 (2.01) 1.0 (2.01)
NOTE:
The transmission capacity varies according to the tractor configurations. Make sure the oil
level is correct.
Apart from this, add oil when operating with hydraulic control valve implements, making sure
the oil level is not too low when all cylinders are extended.
To Next Page
Loading...
