MASSEY FERGUSON 4610 - Transmission Specifications

6.2.1 Removing the fender .............................................6-17
6.2.2 Installing the fender ..............................................6-18
6.3 Engine cover ......................................................6-19
6.3.1 Removing the engine cover ........................................6-19
6.3.2 Installing the engine cover .........................................6-19
6.3.3 Head lamp and engine cover net ....................................6-19
6.3.4 Side cover .....................................................6-20
6.4 Three-point linkage and drawbar ...................................6-21
6.4.1 Three-point linkage ..............................................6-21
6.4.1.1 Draw bar ...............................................6-26
6.4.1.2 Maintaining drawbar components .............................6-26
6.4.2 Removing the lift cylinder case .....................................6-27
6.5 Rear axle .........................................................6-29
6.5.1 General Information ..............................................6-29
6.5.2 Rear axle and brakes .............................................6-29
6.5.3 Rear differential lock system and housing ..............................6-31
6.6 Rear axle housing and differential gears ............................6-32
6.6.1 Disassembling the rear axle housing ..................................6-32
6.6.2 Inspecting the rear axle and the brakes ................................6-34
6.6.3 Brake discs ....................................................6-34
6.6.4 Separator plates ................................................6-35
6.7 Ring gear and pinion ..............................................6-36
6.7.1 Removing the ring gear and the pinion ................................6-36
6.7.2 Disassembling the ring gear and the pinion .............................6-37
6.7.3 Inspecting the ring gear and pinion assembly ...........................6-38
6.7.4 Assembling the ring gear and the pinion ...............................6-38
6.7.5 Installing the ring gear and the pinion .................................6-42
6.7.6 Backlash specification ............................................6-42
6.7.7 Thrust collar specification .........................................6-43
6.7.8 Tooth contact pattern ............................................6-43
6.7.9 Assembling the pinion bevel .......................................6-45
6.8 Brakes ...........................................................6-46
6.8.1 Disassembling the brakes .........................................6-47
6.8.2 Inspecting the brake discs and the separator plates .......................6-47
6.8.3 Checking the brake adjustment .....................................6-47
6.8.4 Adjusting the brakes .............................................6-48
6.9 Differential .......................................................6-49
6.9.1 Differential lock .................................................6-49
6.10 Front axle .......................................................6-51
6.10.1 Removing the front axle ..........................................6-51
6.10.2 Front axle component inspection ...................................6-52
6.10.3 Installing the front axle ...........................................6-54
6.10.4 Front axle components ..........................................6-55
6.10.5 Front axle specifications .........................................6-57
6.10.6 Four-wheel drive shaft components .................................6-57
6.10.7 Hydraulic steering ..............................................6-58
6.10.8 Two-wheel drive front axle component ...............................6-60
6.10.9 Two-wheel drive steering controller system ...........................6-63
6.10.10 Two-wheel drive tie rod system ...................................6-63
6.11 Front differential (four-wheel drive only) ...........................6-64
6.11.1 Disassembling the pinion carrier ....................................6-64
6.11.2 Overhauling the pinion carrier ......................................6-65
6.11.3 Inspecting the pinion carrier .......................................6-66
6.11.4 Assembling the pinion carrier ......................................6-66
6.11.5 Disassembling the differential gears .................................6-67
6.11.6 Inspecting the differential gears ....................................6-67
Table of contents
4608 / 4609 / 4610 Service Manual
4283492M3