Master Heat Gun HG-801D Series User Manual

5
4
4. To turn heat gun
off after use, move
switch to “I” position.
Run on cold for
approximately three
minutes. This will
allow the heat gun to cool down and the
nozzle to become cool to the touch.
5. Move switch to
"O" position.
1. Plug heat gun into properly rated outlet.
2. Move rocker switch to “II” position. (VT
Models, turn heat control to desired
heat setting). Heat
gun will come up
to full operating
temperature in
approximately two
minutes.
3. Adjustable stand
is provided to allow
nozzle to be rotated
from almost horizontal
to vertical position.
ImportantSafetyInformation•Readallsafetyinformationbeforeoperating
equipment. Save these instructions
Important Safety Instructions Repair and Maintenance Instructions
• Cleanupallremovedpaintanddust
by wet mopping the oors. Use a wet
cloth to clean all walls, sills and any other
surface where paint or dust is clinging. DO
NOTSWEEP,DRYDUSTORVACUUM.
Use a high phosphate detergent or
trisodium phosphate (TSP) to wash and
mop areas.
• Attheendofeachworksessionput
the paint chips and debris in a double
CLEANING
REPAIR AND MAINTENANCE INSTRUCTIONS
TO OPERATE HEAT GUN
MASTER HEAT GUN® REPLACEMENT PARTS (HG/VT MODELS)
5-20P
G
W
All repairs and maintenance must be
performed by a qualied repair technician
who is experienced with the repair of electric
tools, a qualied service organization, or
Master Appliance Corp.’s Repair Department.
Please contact Master’s Customer Service
Department for genuine Master Appliance
replacement parts or for repair service.
Unplug heat gun before cleaning. To clean
outside of tool, use only a mild soap and
damp cloth. Do not use other cleaning
agents, turpentine, gasoline, lacquer or paint
thinner, or other solvents that may contain
Master Heat Gun® replacement parts
and accessories are engineered and
manufactured to precise MASTER
APPLIANCE specication. Replacement
parts and accessories from other
manufacturers are not produced to these
precise specications and therefor may
cause difficulties with or actually cause
damage to your Master Heat Gun®. Master
Appliance cannot assume responsibility
or liability for difficulties or damage
resulting from the use of any other brand of
replacement parts or accessories with your
Master Heat Gun®.
chemicals which are harmful to plastics and
other insulating materials. Never immerse
tool in a liquid or allow a liquid to enter inside
the tool. Make sure all vents and openings
are free and clear of debris.
NOTICE:When heat gun is used in an
enclosed container, such as a shrink tunnel
or special enclosure, ambient air must be
allowed to pass into the heat gun and there
must be an outlet of equal size for the heated
air to pass out of the enclosure also. Total
enclosure will cause damage or possible
failure to the heat gun due to the extreme
heat generated.
plastic bag, close it with tape or twist ties,
and dispose of properly.
• Removeprotectiveclothingandwork
shoes in the work area to avoid carrying
dust into the rest of the dwelling. Wash
work clothes separately. Wipe shoes off
with a wet rag that is then washed with
the work clothes. Wash hair and body
thoroughly with soap and water.
SPECIFICATIONS
Size ...........10”Lx5-1/4”Wx9-1/2”H
Nozzle opening .............1-3/16” dia.
Nozzle shield length ...........4-7/8" L
Average air velocity 3400 FPM at ambient
Average air volume ...27 CFM at ambient
Net weight (with stand) 3.7lbs.(D-models)
. . . . . . . . . . . . . . . . . . . . 2.8 lbs. (T-models)
Cord Length ....................6 Ft. L
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON ‘COLD’
BEFORE TURNING OFF.
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
A LA SORTIE.
DU BEC OPÉRER À ‘COLD’
AVANT DE FERMER
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON ‘COLD’
BEFORE TURNING OFF.
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
A LA SORTIE.
DU BEC OPÉRER À ‘COLD’
AVANT DE FERMER
4
3
2
1
5
6
7
8
9
Model °F °C Voltage Amps Was Element
HG-201D/T 400 204 120 5 600 30087
HG-301D/T 800 426 120 12 1440 30085
HG-501D/T 1200 649 120 14.5 1740 30083
HG-801D* 1400 760 120 18.5 2220 30082
HG-202D/T 400 204 220 3 660 30088
HG-302D/T 800 426 220 6 1320 30086
HG-502D/T 1200 649 220 9 1980 30084
* Required 20A outlet, equipped with NEMA 5-20P Plug
Temperature
Master Heat Gun®
Replacement
Model °F °C Voltage Amps Was Element
VT-751D 100-1200 38-649 120 14.5 1740 30083
VT-752D 100-1200 38-649 220 9 1980 30084
Temperature
Master Varitemp® Heat Gun
Replacement
Model °F °C Voltage Amps Was Element
HG-201D/T 400 204 120 5 600 30087
HG-301D/T 800 426 120 12 1440 30085
HG-501D/T 1200 649 120 14.5 1740 30083
HG-801D* 1400 760 120 18.5 2220 30082
HG-202D/T 400 204 220 3 660 30088
HG-302D/T 800 426 220 6 1320 30086
HG-502D/T 1200 649 220 9 1980 30084
* Required 20A outlet, equipped with NEMA 5-20P Plug
Temperature
Master Heat Gun®
Replacement
Model °F °C Voltage Amps Was Element
VT-751D 100-1200 38-649 120 14.5 1740 30083
VT-752D 100-1200 38-649 220 9 1980 30084
Temperature
Master Varitemp® Heat Gun
Replacement
-CAUTION-
HIGH TEMPERATURE AT
NOZZLE. RUN ON ‘COLD’
BEFORE TURNING OFF.
-ADVERTENCIA-
ALTA TEMPERATURA EN LA
BOQUILLA. ANTES DE
APAGAR LA HERRAMIENTA.
A LA SORTIE.
DU BEC OPÉRER À ‘COLD’
AVANT DE FERMER
WARNING-ToReduceTheRisk
Of Fire Or Electric Shock, Connect To
GroundedOutlet.DoNotExposeTo
Rain Or Moisture. Store Indoors; Read
Instruction Manual Before Using.
CAUTION-HIGHTEMPERATURE
ATNOZZLE.RUNONCOLDBEFORE
TURNINGOFF.

Master Heat Gun HG-801D Series Specifications

General

Brand	Master
Model	Heat Gun HG-801D Series
Category	Power Tool
Language	English