Master SET User Manual

This function allows to move the motor with short steps. If the function is active, the commands «orientation
Right» and «orientation Left» (see the User manual of you transmitter) move the motor with short clicks. This
function can be given also through the manual command. In order to activate the manual command, briefly press
one of the two buttons (less than 0,5 seconds), then press it again and hold it until reaching the opening with the
desired microclicks.
To modify the orientation function through the transmitter:
09. TILTING FUNCTION
Advanced Info
All products and technical specifications given in this document are subject to variation without notice.
The manufacturer shall not be liable for damage resulting from improper, incorrect or unreasonable use.
N° of movements
Setting
1
2
3
4
5
INACTIVE
50 msec
100 msec
150 msec
200 msec
10. RESET
10.1 USING A TRANSMITTER
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters
01.
If possible, bring the motor to the intermediate position.
02. Disconnect the power supply.
03. Connect as on the diagram.
04. Connect the power supply. Wait 30 seconds, the motor makes a signal.
05. Disconnect the power supply.
06. Restore the connections (see diagram on section 3).
07. Reinstall the motor (see section 05).
10.2 USING COMMAND BUTTONS
01. Bring the motor in an intermediate
position.
02. Press MENU for about 5 sec, until
«rS» appears on display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes,
the motor performs some movement
05. Press together PREV and NEXT for
about 2 seconds until the motor
indicates that the reset was
performed (1 moving up / down).
06. Reinstall the motor (see section 05).
01. Bring the motor in an intermediate
position.
02. Holding down STOP, press PROG
for about 1 sec, until LEDs light
03. Press 2 time UP / 9 times DOWN.
04. Press STOP. The LEDs flash, the
motor performs some movement
05. Press together UP and DOWN for
about 2 seconds until the motor
indicates that the reset was
performed (1 moving up / down).
06. Reinstall the motor (see section 05).
01. Bring the motor in an intermediate
position.
02. Press MENU, «Menu rx» appears
on display
03. Press 2 time PREV / 9 times NEXT.
«29» appears on display
04. Press STOP. The display flashes,
the motor performs some movement
05. Press together PREV and NEXT for
about 2 seconds until the motor
indicates that the reset was
performed (1 moving up / down).
06. Reinstall the motor (see section 05).
See the User manual
of the transmitter at
section:
«RECEIVER MENU -
Function 29»
L (phase)
N (neutral)
motor
cable
gray
brown
blue
yellow/green
black
Before performing the “reset” from the transmitter:
ü On the transmitter select the radio channel which commands the device to be resetted.
ü Ensure that this radio channel commands only the device you need to reset.
See the User manual
of the transmitter at
section:
«RECEIVER MENU -
Function 12»
ARCO
FLUTE, KUADRO, KORT
VISIO
Other transmitters...
01. Bring the motor in an intermediate
position.
02. Press MENU for about 5 sec, until
«rS» appears on display
03. Press 1 time PREV / 2 times NEXT.
«12» appears on display
04. Press STOP. The motor signals the
current value (1 to 5 movements)
05. Press NEXT the number of times
equal to the desired setting (1 to 5)
06. Press STOP. The motor signals the
new value (1 to 5 movements)
01. Bring the motor in an intermediate
position.
02. Holding down STOP, press PROG
for about 1 sec, until LEDs light
03. Press 1 time UP / 2 times DOWN.
04. Press STOP. The motor signals the
current value (1 to 5 movements)
05. Press DOWN the number of times
equal to the desired setting (1 to 5)
06. Press STOP. The motor signals the
newt value (1 to 5 movements)
01. Bring the motor in an intermediate
position.
02. Press MENU, «Menu rx» appears
on display
03. Press 1 time PREV / 2 times NEXT.
«12» appears on display
04. Press STOP. The motor signals the
current value (1 to 5 movements)
05. Press UP the number of times equal
to the desired setting (1 to 5)
06. Press STOP. The motor signals the
new value (1 to 5 movements)

Master SET Specifications

General

Brand	Master
Model	SET
Category	Engine
Language	English