08
08. HOW TO MEMORIZE/DELETE A RADIO DEVICE
01. Bring the motor in an intermediate position.
02. Press PROG of an already memorized transmitter for 5 s. The motor performs 2
upward movements.
03. Within 15 seconds, to memorize/delete:
a transmitter: press of transmitter you want to memorize/deleteSTOP
a rain sensor: press « » of rain sensor you want to memorize/deleteP2
04. 1 upward movement: device memorized!!
1 downward movement: device deleted!!
2 downward movement: error!!
PROG
(5 seconds)
NOTE:
point 04. "error"is reported if the radio code is not received in time or if the receiver's memory is full or if you try to delete the only memorized transmitter,
01. Bring the motor in an intermediate position.
02. Within 15 seconds, press (briefly and quickly).UP 8 times
The motor performs 3 upward movements.
03. Within 15 seconds, press (briefly and quickly).UP 3 times
The motor performs 2 upward movements.
04. Within 15 seconds, to memorize/delete:
a transmitter: press of transmitter you want to memorize/deleteSTOP
a rain sensor: press « » of rain sensor you want to memorize/deleteP2
05. 1 upward movement: device memorized!!
1 downward movement: device deleted!!
2 downward movement: error!!
NOTE:
point 06. "error"is reported if the radio code is not received in time, if the receiver's memory is full; with this procedure you can delete the only memorized transmitter
08.1 USING A TRANSMITTER
08.2 USING COMMAND BUTTONS
STOP
P2
P2
STOP
P2
P2
3 x UP
09. FINE ADJUSTMENT OF POSITION 3 «ROLLER SHUTTER UP»
(*) briefly press, max 2 seconds between each press and the next.
01. Bring the motor to the position 3 (or near).
02. Press in sequence the buttons(*).STOP - PROG - UP
The motor makes 1 downward movement.
03. Using and adjust the position 3.UP DOWN
04. Press . The motor makes 1 down/up movement.PROG
WARNING:
The modification of the upper limit switch is not possible if the upper limit switch has been learned by contact with an obstacle.
10. FINE ADJUSTMENT OF POSITION 2 «CLOSE SLATS»
(*) briefly press, max 2 seconds between each press and the next.
01. Bring the motor to the position 2 (or near).
02. Press in sequence the buttons(*).STOP - PROG - DOWN
The motor makes 1 downward movement.
03. Using and adjust the position 2.UP DOWN
04. Press . The motor makes 1 up/down movement.PROG
STOP
PROG
DOWN
PROG
12. MODIFY BOTH THE LIMIT SWITCHES
(*) briefly press, max 2 seconds between each press and the next.
01. Bring the motor in an intermediate position.
02. Disconnect power supply, wait a few seconds; connect power supply.
03. Within 15s, press in sequence the buttons(*).STOP - PROG - STOP
The motor makes 1 up/down movement; motor moves downward.
04. Depending on how the roller shutter is installed, follow the instructions at point 5
and following of the paragraphs 07.1 or 07.2 or 07.3 or 07.4
STOP
PROG
STOP
WARNING:
If the procedure is not completed, the motor automatically sets a short stroke. In case of interruption of the procedure it is necessary to repeat it completely.
Go to point 5
and following of
the paragraphs
07.1 or 07.2 or
07.3 or 07.4
ON
STOP
PROG
UP
PROG
8 x UP
11. FINE ADJUSTMENT OF POSITION 1 «OPEN SLATS»
(*) briefly press, max 2 seconds between each press and the next.
01. Bring the motor to the position 1 (or near).
02. Press in sequence the buttons(*).STOP - PROG - DOWN
The motor makes 1 downward movement.
03. Using and adjust the position 1.UP DOWN
04. Press . The motor makes 1 up/down movement.PROG
STOP
PROG
DOWN
PROG
WARNING:
The modification of the lower limit switch is not possible if the lower limit switch has been learned by contact with an obstacle.
This motor is compatible with the X11C radio rain sensor associated with the AT12 power supply.
This motor can not be associated with radio wind sensors and radio wind / sun sensors.
13. COMPATIBILITY WITH RADIO SENSORS
WARNING:
Once adjustment of position 1 is complete, position 2 must be checked and adjusted (see paragraph 10)
To Next Page
Loading...
Need help?
General
