Integrity Bath MB-80 Operating Instructions
______________________________________________________________________________________________
MB-80 Operations 2/18/13 800.798.5867
Bath Oil/Shampoo Dispensing System and Aromatherapy
Operating Instructions
BATH OIL
SHAMPOO
MasterCare
Dispensing Control Panel
Dispensing
Buttons
Green LED
Red LED
Red LED
Cap With
Dispensing
Hose
Strainer
Foot
Ceramic
Weight
Aroma Therapy
Dispenser
Cap
GFCI
Reset
To Dispensing
Head Inside Tub
Oil/Shampoo
One Gallon
Jugs
Bottom of
One Gallon
Jug
Access Cap
1) Before activating the BathAire remove the Aromatherapy Access Cap and insert the sachet with the selected scent you want to
use for the bath. “DO NOT OPEN THE SACHET”, DO NOT place loose beads or liquids in the sachet holder. Securely close the
cap prior to turning on BathAire CAUTION: Running the BathAire without the sachet cap securely in place will cause the
system to lose too much air and the aerators (hydromassage action) will not function properly. If the sachet will not easily fit
into the sachet holder, slowly slide the zip tie up the sachet making the sachet more elongated. DO NOT REMOVE THE ZIP
TIE.
Bath Oil/Shampoo Dispensing Operation:
1) Press Bath Oil or Shampoo button briefly to initiate pump cycle. If using Bath Oil, allow it to dispense directly into the bath water.
If using Shampoo, hold hand under the dispensing head inside tub wall. If more solution is required, press button a second time. The
amount of bath oil and shampoo dispensed is preset for economic portions at the factory. If you need more solution, press the button
a second time.
2) If no solution is dispensed from the dispensing head, open the service door to access the solutions storage. Check the fluid level in
the one liter bottle. If below the intake hose, replace with MasterCare’s Bath Oil or Shampoo per priming instructions below.
Note: 1) If you press Bath Oil or Shampoo button for more than five seconds, it will initiate a pump prime
cycle.
2) The normal pump cycle can finish and turn off before the five seconds occurs, but it will still enter Prime
and turn back on.
3) Holding a Button for a longer time will not cause any problems other than initiating Prime.
4) Pressing any button while a pump is running will shut off the pump. This is predominately a safety feature
for the Prime operation.
5) Pressing multiple buttons at the same time will turn off any pumps and be otherwise ignored.
6) A Red LED associated with the pump operation will turn on when the pump operation is activated. The middle Red LED is for Bath
Oil. The bottom Red LED is for Shampoo.
7) See the maintenance instructions for the purpose and function of the Green LED.
Replacing One Liter Jugs & Priming Operation:
1) Remove the empty one liter container of solutions and replace with MasterCare’s Bath Oil or Shampoo.
2) Remove the cap and seal under the cap on the one liter jug of cleaner disinfectant.
3) Insert the foot strainer attached to the cap with dispensing hose into the one liter jug so that the strainer foot is on the bottom of the
jug. If replacing an empty one liter container check the strainer at the bottom of the foot stainer. Remove any accumulated debris that
can clog it up.
4) To prime, push appropriate button for the solution you are priming for seven seconds.
Caution: Other brand bath oils and shampoos may be used with the MasterCare System although re-calibration may be required.
However, some products may not be compatible with the system and may damage components in the system, thereby voiding the
warranty. MasterCare offers an extended warranty with your use of MasterCare bathing and cleaning/disinfection products.
Please
contact MasterCare customer service @ 800-798-5867 before using non-MasterCare products in your system. Form 00025D
To Next Page
Loading...
