Matco Tools MT1815 - Air Supply; Troubleshooting; Lubrication and Maintenance; Warranty

MT1815 3 04/30/12
MT1815 Long Barrel Air Hammer
WarranTy
Matcowarrantsitsairtoolsforaperiodof1yeartotheconsumer.Wewill
repairanyMTSeriesairtoolcoveredunderthiswarrantywhichprovestobe
defective in material or workmanship during the warranty period. In order
tohaveyourtoolrepaired,returnthe toolto eitherof theMatcoAuthorized
WarrantyCenterslistedtotheright,freightprepaid.Pleaseincludeacopyof
yourproof ofpurchaseandabrief descriptionoftheproblem.The toolwill
beinspectedandifanypartorpartsarefoundtobedefectiveinmaterialor
workmanship, the tool will be repaired free of charge and returned to you
freight prepaid.
Thiswarrantygivesyouspecificrights.Youmayalsohaveotherrightswhich
varyfromstatetostate.
The foregoing obligation is Matco’s sole liability under this or any implied
warrantyandundernocircumstancesshallMatcobeliableforanyincidental
or consequential damages.
Note: Some states do not allow the exclusion or limitation of
incidentalorconsequentialdamagessotheabovelimitationorexclusionmay
notapplytoyou.
air supply
Tools of this class operate on a wide range of air pressures. It is
recommended that air pressure of these tools measures 90 PSI at the tool
while running free. Higher pressure and unclean air will shorten tool life
becauseoffasterwearandmaycreateahazardouscondition.
Waterintheairlinewillcausedamagetothetool.Draintheairtankdaily.Clean
the air inlet filter screen on at least a weekly schedule.The recommended
hook-upprocedurecanbeviewedinFigure1.
The air inlet used for connecting air supply has standard 1/4" NPT
American Thread.
Linepressureshouldbeincreasedtocompensateforunusuallylongairhoses
(over 25 feet). Minimum hose diameter should be 3/8" I.D. and fittings should
have the same inside dimensions.
TrouBleshooTing
Other factors outside the tool may cause loss of power or erratic action.
Reduced compressor output, excessive drain on the air line, moisture or
restrictions in air pipes or the use of hose connections of improper size or poor
conditionsmayreduce airsupply.If outsideconditionsare inorder,andthe
toolstillperformserratically,disconnecttoolfromhoseandtaketooltoyour
nearest Matco authorized service center.
luBricaTion & MainTenance
Lubricatethetooldailywithagoodgradeofairtooloil.Ifnoairlineoileris
used, run 1/2 oz. of oil through the tool. The oil can be squirted into the tool air
inletorintothehoseatthenearestconnectiontotheairsupply,thenrunthe
tool. A rust inhibitive oil is acceptable for air tools.
Nipple
feaTures
•Integrated chuck on barrel.
•Variablespeedtriggerforcontrol.
•Metalvalveassemblyforincreaseddurability.
•Lighter fluted barrel for easier use.
•Rubberbumpervibrationdampeningforcomfortableuseoverextendedperiodsoftime.
•Center handle design for superior balance during use.
•Comfort,power,anddurabilityatitsbest.
Figure 1
MATCO AIR COMMANd
ToolRepairSV
1330 Commerce Dr.
Stow,OH44224
(800) 433-7098
dISCOuNT TOOL REPAIR
3433 Losee Rd. #1
NorthLasVegas,NV89030
(702) 657-6570
PNEuTOOL PARTS &
SERVICES CO., LTd
33 Haas Road
Toronto,ONM9W3A1Canada
(416) 748-1200
(888) 748-1201 (Toll-Free in
Canada)
dIVERSIFIEd POWER
INC.
90 Buttermill Avenue,
Vaughan,Ontario
L4K3X7Canada
Tel: 905-760-9077
Toll Free: 800-821-7975