What to do if my Mathias Bauerle Multipli 35 Folding Machines folder does not run?
If your Mathias Bauerle Folding Machines folder doesn't run, ensure the pump is switched on. If the pump is off, switch it on.
What to do if Mathias Bauerle Folding Machines are feeding several sheets together?
If several sheets are being fed together in your Mathias Bauerle Folding Machines, it could be due to the gap between the feed and pressure roller being too narrow. Increase the gap using the setting disk. Alternatively, you may need to change the height by means of the setting screw.
What to do if there is a paper jam at the entrance into the fold plates of Mathias Bauerle Multipli 35?
If there is a paper jam at the entrance into the fold plates of your Mathias Bauerle Folding Machines, clear the jam. Then, switch the machine off and then on again.
Why is the sheet gap not being set correctly on my Mathias Bauerle Multipli 35 Folding Machines?
If the sheet gap cannot be set correctly on your Mathias Bauerle Folding Machines even though the display shows changes, it may be because the sheet gap photodetector setting is either too sensitive or not sensitive enough. Try reducing the sensor sensitivity at the potentiometer of the sheet gap photodetector using a screwdriver until the LED goes out. Another possible cause is a dirty sheet gap photodetector. Clean the bottom of the photodetector with a soft cloth or a brush.
What to do if there is no feed in Mathias Bauerle Folding Machines?
If there is no feed in your Mathias Bauerle Folding Machines, it could be due to insufficient infeed roller pressure or a worn infeed roller. Increase the pressure using the knurled nut on the feeder or replace the roller. You can also slide the hold-down disks on the feed shaft outward somewhat.
How to fix fold variations in Mathias Bauerle Folding Machines?
To correct fold variations in Mathias Bauerle Folding Machines, adjust the air brackets according to the scale.
How to fix sheets not evenly fanned on delivery in Mathias Bauerle Folding Machines?
To fix sheets not being evenly fanned on delivery in your Mathias Bauerle Folding Machines, arrange the ejector rollers evenly across the paper width.
How to fix intermittent and irregular paper feed in Mathias Bauerle Folding Machines?
To address intermittent and irregular paper feed in Mathias Bauerle Folding Machines, set with a little more side play.
Provides guidance on machine installation, repairs, service, and inspections.
Instructions and warnings for safe transport and initial setup.
Explains essential safety warnings, symbols, and basic operation precautions.
Covers organizational measures, personnel selection, and responsibilities for safety.
Details safety for standard operation and special work like maintenance and repair.
Highlights specific dangers and safety instructions for cleaning and maintenance.
Highlights specific dangers and safety instructions for cleaning and maintenance.
Highlights specific dangers and safety instructions for cleaning and maintenance.
Highlights specific dangers and safety instructions for cleaning and maintenance.
Highlights specific dangers and safety instructions for cleaning and maintenance.
Explains the function and suitability of the friction feeder for different papers.
Explains the air and vacuum separation principle of the S32 air feeder.
Explains the air and vacuum separation principle of the PBA 35 air feeder.
Instructions for performing trial folds and making minor corrections with the friction feeder.
Instructions for performing trial folds with S and PBA models without an operator panel.
Instructions for performing trial folds with the PBA model with an operator panel.
Explains how to adjust the fold length using the fine adjustment screw.
Details how to identify and correct skewed or out-of-square folds.
Provides methods for correcting skewed folds and out-of-square paper feed.
Safety precautions for removing and installing perforating and slitting knives.
Explains the photodetector's function and the paper weight range covered.
Step-by-step guide for setting and calibrating the double sheet detection.
Lists common paper feed and folding problems with their potential causes.
Provides remedies for various feed, fold, and delivery belt issues.
Addresses issues related to sheet gap photodetector sensitivity and dirt.
General| Brand | Mathias Bauerle |
|---|---|
| Model | Multipli 35 |
| Category | Folding Machines |
| Language | English |
To Next Page