Matrix MG-A422 - User Manual

To Next Page

MAGNUM SERIES

MG-A422 / VERTICAL BENCH PRESS

MAINTENANCE CHECKLIST

ACTION FREQUENCY

Clean Upholstery * Daily

Inspect Cables Daily

Clean Guide Rods Monthly

Inspect Hardware Monthly

Inspect Frame Bi-Annually

Clean Machine As Needed

Clean Grips * As Needed

Lubricate Guide Rods † As Needed

* Upholstery & Grips should be cleaned with a mild soap and

water or a non-ammonia based cleaner.

† Guide rods should be lubricated with Teon based lubricant. Apply

the lubricant to a cotton cloth and then apply up and down the

guide rods.

PRODUCT SPECIFICATIONS

TECH SPECS

Maximum User Weight 159 kg / 350 lbs.

Maximum Training Weight 245 kg / 540 lbs.

Product Weight 138 kg / 305 lbs.

Overall Dimensions

(L x W x H)*

122 x 163 x 198 cm /

48" x 64" x 78"

Weight Horn Diameter

(Weight Plate Storage)

47.63 mm / 1.875”

* Ensure a minimum clearance width of 914 mm / 36” for access

to and passage around MATRIX strength equipment.

WARRANTY

Valid in North America only

Frame (not coatings) * 10 years

Weight stacks 5 years

Pulleys 5 years

Pivot bearings 5 years

Any items not specied 3 years

Labor (excludes upholstery/cables/grips) 3 years

Upholstery/cables/grips/springs 1 year

* Frame is dened as the welded metal base of the unit and does

not include removable parts.

PROPER USAGE

1. Do not exceed weight limits of the

exercise device.

2. If applicable, set safety stops to

appropriate height.

3. If applicable, adjust seat pads, leg pads,

foot pads, range of motion adjustment, or

any other type of adjustment mechanisms

to a comfortable start position. Make

certain that the adjusting mechanism is

fully engaged to prevent unintentional

movement and to avoid injury.

4. Sit on bench (if applicable) and get into

appropriate position for exercise.

5. Exercise using no more weight than you

can safely lift and control.

6. In a controlled manner, perform exercise.

7. Return weight to its fully-supported start

position.

MX13_MAGNUM_OM_MG-A422_r1_0.indd 1 6/18/13 10:28 AM

Need help?

Do you have a question about the Matrix MG-A422 and is the answer not in the manual?

The Matrix Magnum Series MG-A422 Vertical Bench Press is a strength training machine designed for upper body workouts, specifically targeting the chest muscles. It is part of the Magnum Series, known for robust construction and effective exercise performance.

Function Description

The device allows users to perform vertical bench press exercises in a controlled manner. It features a guided motion path, which helps in isolating the target muscles and ensuring proper form throughout the exercise. The machine is designed to accommodate various user sizes and strength levels, providing a safe and effective workout experience.

Important Technical Specifications

Maximum User Weight: 159 kg (350 lbs.)
Maximum Training Weight: 245 kg (540 lbs.)
Product Weight: 138 kg (305 lbs.)
Overall Dimensions (L x W x H): 122 x 163 x 198 cm (48" x 64" x 78")
Weight Horn Diameter (Weight Plate Storage): 47.63 mm (1.875")
Clearance: A minimum clearance width of 914 mm (36") is required for access to and passage around Matrix strength equipment.
Stability: The equipment meets industry standards for stability and is in compliance with EN 957-1, EN 957-2, and EN 957-4.
Securing Equipment: Manufacturer recommends securing all stationary Matrix strength equipment to the floor to stabilize and eliminate rocking or tipping. This must be performed by a licensed contractor, with anchor points capable of withstanding 750 lbs. (3.3 kN) pull-out force.

Usage Features

The MG-A422 Vertical Bench Press emphasizes proper usage for safety and effectiveness:

Weight Limits: Users must not exceed the specified weight limits of the device.
Adjustments: If applicable, users should adjust seat pads, leg pads, foot pads, range of motion, or other adjustment mechanisms to a comfortable start position. It is crucial to ensure that the adjusting mechanism is fully engaged to prevent unintentional movement and injury.
Safety Stops: If present, safety stops should be set to the appropriate height. For equipment with adjustable stops, the proper height depends on the exercise performed. This involves removing weight from the lifting bar, performing the exercise to determine the lowest comfortable bar position without spinal compression or contacting the body, positioning both stop catches to stop the bar at this point, ensuring they are fully seated, and then loading weights and performing the exercise. Adjustable safety stops must be used at all times.
Exercise Execution: Users should sit on the bench (if applicable) and get into the appropriate position for exercise. Exercise should be performed using no more weight than can be safely lifted and controlled, in a controlled manner. After exercise, the weight should be returned to its fully-supported start position.
Spotter: Always use a spotter when operating this equipment.
Adjustable Mechanisms: When adjusting any mechanism (seat position, pad location, range of motion limiter, pulley carriage, or any other type of adjuster), ensure the adjusting pin is fully engaged in the hole to avoid injury.
General Safety: Keep body, hair, clothing, and fitness accessories free and clear of all moving parts. Keep hands and feet clear from moving parts at all times. Never allow children on strength training equipment; teenagers must be supervised. Do not use resistance straps, ropes, or other means attached to the equipment, or for support during stretching, as this may result in serious injury.
Health Precautions: Injuries to health can result from incorrect or excessive training. Users should cease exercise if they feel faint or dizzy and obtain a medical exam before beginning an exercise program.

Maintenance Features

Regular maintenance is crucial for smooth operation and longevity of the equipment.

Upholstery & Grips: Clean daily with a mild soap and water or a non-ammonia based cleaner.
Cables: Inspect daily.
Guide Rods: Clean monthly and lubricate monthly with Teflon-based lubricant. Apply lubricant to a cotton cloth and then apply up and down the guide rods.
Hardware: Inspect monthly.
Frame: Inspect bi-annually.
Machine: Clean as needed.
Damaged Parts: Do not use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by your country's local Matrix dealer.
Labels and Nameplates: Do not remove labels. If unreadable or missing, contact your Matrix dealer for a replacement.
Preventative Maintenance: Equipment needs to be inspected at regular intervals. Any person performing adjustments or maintenance must be qualified. Matrix dealers provide service and maintenance training.
Warranty (Valid in North America only):
- Frame (not coatings): 10 years
- Weight stacks: 5 years
- Pulleys: 5 years
- Pivot bearings: 5 years
- Any items not specified: 3 years
- Labor (excludes upholstery/cables/grips): 3 years
- Upholstery/cables/grips/springs: 1 year
- Frame is defined as the welded metal base of the unit and does not include removable parts.

This equipment is intended for use in supervised areas where access and control are regulated by the owner. The owner should consider a user's reliability, age, and experience.