Matrix MG-A435 - User Manual

To Next Page

MAGNUM SERIES

MG-A435 / LAT PULLDOWN

MAINTENANCE CHECKLIST

ACTION FREQUENCY

Clean Upholstery * Daily

Inspect Cables Daily

Clean Guide Rods Monthly

Inspect Hardware Monthly

Inspect Frame Bi-Annually

Clean Machine As Needed

Clean Grips * As Needed

Lubricate Guide Rods † As Needed

* Upholstery & Grips should be cleaned with a mild soap and

water or a non-ammonia based cleaner.

† Guide rods should be lubricated with Teon based lubricant. Apply

the lubricant to a cotton cloth and then apply up and down the

guide rods.

PRODUCT SPECIFICATIONS

TECH SPECS

Maximum User Weight 159 kg / 350 lbs.

Maximum Training Weight 245 kg / 540 lbs.

Product Weight 95 kg / 210 lbs.

Overall Dimensions

(L x W x H)*

178 x 132 x 208 cm /

70" x 52" x 82"

Weight Horn Diameter

(Weight Plate Storage)

47.63 mm / 1.875”

* Ensure a minimum clearance width of 914 mm / 36” for access

to and passage around MATRIX strength equipment.

WARRANTY

Valid in North America only

Frame (not coatings) * 10 years

Weight stacks 5 years

Pulleys 5 years

Pivot bearings 5 years

Any items not specied 3 years

Labor (excludes upholstery/cables/grips) 3 years

Upholstery/cables/grips/springs 1 year

* Frame is dened as the welded metal base of the unit and does

not include removable parts.

PROPER USAGE

1. Do not exceed weight limits of the

exercise device.

2. If applicable, set safety stops to

appropriate height.

3. If applicable, adjust seat pads, leg pads,

foot pads, range of motion adjustment, or

any other type of adjustment mechanisms

to a comfortable start position. Make

certain that the adjusting mechanism is

fully engaged to prevent unintentional

movement and to avoid injury.

4. Sit on bench (if applicable) and get into

appropriate position for exercise.

5. Exercise using no more weight than you

can safely lift and control.

6. In a controlled manner, perform exercise.

7. Return weight to its fully-supported start

position.

MX13_MAGNUM_OM_MG-A435_r1_0.indd 1 6/18/13 10:29 AM

Need help?

Do you have a question about the Matrix MG-A435 and is the answer not in the manual?

The Matrix Magnum Series MG-A435 Lat Pulldown is a strength training machine designed for targeting the latissimus dorsi muscles. It is part of the Magnum Series, indicating a robust and commercial-grade build.

Function Description:

The device allows users to perform lat pulldown exercises, which primarily target the latissimus dorsi, biceps, and rear deltoids. Users sit on a bench and pull a bar attached to a cable system downwards, engaging the back muscles. The machine utilizes a weight stack for resistance, which can be adjusted to suit the user's strength level. The design emphasizes controlled movement and proper form to maximize exercise effectiveness and minimize injury risk.

Important Technical Specifications:

Maximum User Weight: 159 kg / 350 lbs.
Maximum Training Weight: 245 kg / 540 lbs.
Product Weight: 95 kg / 210 lbs.
Overall Dimensions (L x W x H): 178 x 132 x 208 cm / 70" x 52" x 82".
Weight Horn Diameter (Weight Plate Storage): 47.63 mm / 1.875".
Clearance: A minimum clearance width of 914 mm / 36" is required for access to and passage around Matrix strength equipment.
Warranty (Valid in North America only):
- Frame (not coatings): 10 years
- Weight stacks: 5 years
- Pulleys: 5 years
- Pivot bearings: 5 years
- Any items not specified: 3 years
- Labor (excludes upholstery/cables/grips): 3 years
- Upholstery/cables/grips/springs: 1 year
- Frame is defined as the welded metal base of the unit and does not include removable parts.

Usage Features:

Proper usage is critical for safety and effectiveness.

Weight Limits: Do not exceed the specified weight limits of the device.
Adjustments: If applicable, users should adjust seat pads, leg pads, foot pads, range of motion, or other adjustment mechanisms to a comfortable start position. It is crucial to ensure that adjusting mechanisms are fully engaged to prevent unintentional movement and injury.
Positioning: Users should sit on the bench (if applicable) and get into the appropriate position for the exercise.
Controlled Movement: Exercise should be performed using no more weight than can be safely lifted and controlled, in a controlled manner.
Return to Start: After exercise, return the weight to its fully-supported start position.
Safety Precautions:
- Never allow children on strength training equipment; teenagers must be supervised.
- Read all warnings and instructions prior to use.
- Inspect the machine before each use; do not use if damaged or inoperable.
- Never attach resistance straps, ropes, or other means to the equipment, and do not use it for support during stretching.
- Always use a spotter.
- Do not exceed the weight capacity.
- Balance the weight applied and use retention devices for weight discs where applicable.
- Cease exercise if feeling faint or dizzy, and obtain a medical exam before starting a program.
- Keep body, hair, clothing, and fitness accessories clear of all moving parts.
- Manufacturer recommends securing all equipment to the floor to stabilize and eliminate rocking or tipping over, using a licensed contractor. Anchor points must withstand 750 lbs. (3.3 kN) pull-out force.
- Do not remove labels. Replace if damaged or illegible.
- When adjusting any adjustable mechanism (e.g., seat position, pad location, range of motion limiter, pulley carriage), ensure the adjusting pin is fully engaged in the hole to avoid injury.
- Keep hands and feet clear at all times from moving parts.
Installation: The equipment must be installed on a stable, level surface and secured to the floor by a licensed contractor to prevent rocking or tipping.

Maintenance Features:

Regular maintenance is essential for smooth operation, longevity, and safety.

Daily:
- Clean Upholstery: Use a mild soap and water or a non-ammonia based cleaner.
- Inspect Cables.
Monthly:
- Clean Guide Rods: Lubricate with Teflon-based lubricant. Apply to a cotton cloth and then apply up and down the guide rods.
- Inspect Hardware.
Bi-Annually:
- Inspect Frame.
As Needed:
- Clean Machine.
- Clean Grips: Use a mild soap and water or a non-ammonia based cleaner.
- Lubricate Guide Rods.
General Maintenance:
- Do not use damaged or worn parts; use only replacement parts supplied by a local Matrix dealer.
- Maintain labels and nameplates; do not remove them. Contact your dealer for replacements if unreadable or missing.
- Preventative maintenance is key. Equipment should be inspected at regular intervals.
- Ensure that any person performing adjustments or maintenance is qualified. Matrix dealers can provide service and training.