Maxlogic ML-123X Series - User Manual

75 pages

Save Page as PDF

To Next Page

COMMISSIONING, OPERATING AND MAINTENANCE MANUAL

MODEL: MAXLOGIC SERIES

SUB MODEL: INTELLIGENT ANALOGUE

ADDRESSABLE FIRE ALARM CONTROL PANEL

Main Page

Table of Contents3
LIST of FIGURES Figure 1-Loop Card (SLCU) Connection11
Loop Voltage Drop Calculation23
Panel Events23
Fire Condition23
Fault Condition24
System Fault Condition24
Corruptions of Special Data on Site25
System Faults Based on Interface Errors26
Service Personals Needs to Do26
Nd ACCESS LEVEL (USER) CONTROLS and FUNCTIONS26
How to Display Feature/Analogue Measurement Result of Devices in Loops28
How to Disable and Enable Loops28
How to Disable and Enable a Zone29
How to Disable and Enable any Device30
How to Disable and Enable Sounders31
How to Disable and Enable Fire Routing Output31
How to Make Control Panel Time Settings32
How to Display Total Fire Alarm Number33
How to Activate / Deactivate Output Delays33
How to Test a Loop33
How to Test a Zone34
How to Test a Device35
How the Suppressed Fire Events, Fault Events and Other Warnings Are Viewed36
How to View Suppressed Disablement Events36
Rd ACCESS LEVEL (ENGINEERING) CONTROLS and FUNCTIONS37
How to Reach Access Level 3, Which Is Engineering Level37
How to Display General Settings of Fire Alarm Control Panel37
How to Set Resounding Condition after Silencing Alarms with Silence Alarm Button38
How to Set Automatic Reset Time for Test39
How to Set Automatic Reset Time for more than One Alarm Signal in Type a Dependency39
How to Set Automatic Reset Time for more than One Alarm Signal in Type B Dependency40
How to Display Time Values Used for Dar / Night Mode40
How to Display Software Version Data of Processors Used in Control Panel41
How to Display Control Panels in Network42
How to Display Event Logs in Categories42
How to Display Event Logs in Order43
How to Print Event Logs Categorically43
How to Print Event Logs as Being Arranged in Time Sequence44
How to Cancel Printing Event Logs Process44
How to Erase Event Logs45
How to Print Control Panel Settings46
How to Update Software Version of SLCU46
How to Enable Automatic Contamination Check for All Loops47
How to Make Manual Contamination Control for All Loops48
How to See Results of Manual Contamination Control for All Loops49
How to Enable Automatic Contamination Control for any Loop50
How to Make Manual Contamination Control for any Loop51
How to Display the Results of Manual Contamination Control for any Loop52
How to Apply Automatic Learning53
How to Download Site Specific Data from Control Panel54
How to Upload Site Specific Data to Control Panel55
How to Set Output Delay56
How to Alter Data of Devices in Loop57
How to Set Dependency (Pre-Alarm Feature) for more than One Alarm Signal in Type a and B58
How to Set Dependency for more than One Alarm Signal in Type C (Creating Scenario)59
How to Assign Event to Remote Inputs61
How to Modify Control Panel Settings62
How to Set Control Panel Behaviors in Network63
Operations on the Periodic Maintenance64
Annex-A Ml-123X Series Panel Structure65
Annex-B Ml-124X Series Panel Structure66
ANNEX - 2Nd Access Level (User) Menu67
ANNEX - 3Rd Access Level (Engineering) Menu69
ANNEX - Explanations of the Terms72
ANNEX - Abbreviations72
ANNEX - Mechanic and Outside Definitions72
ANNEX - Input / Output Definitions73

Need help?

Do you have a question about the Maxlogic ML-123X Series and is the answer not in the manual?

Maxlogic ML-123X Series Specifications

General

Brand	Maxlogic
Model	ML-123X Series
Category	Control Panel
Language	English

Related product manuals

Maxlogic ML-123X Series - User Manual

Table of Contents

Maxlogic ML-123X Series Specifications

Related product manuals