Maxx Ice MIM130 - User Manual

Questions and Answers

E
Eugene RyanAug 17, 2025
What to do if my Maxx Ice Ice Maker doesn't operate?
- D
  Donna PittsAug 17, 2025
  If your Maxx Ice Ice Maker isn't operating, there are several potential causes and solutions: * Ensure the ice maker is plugged in. * Check the fuse and replace it if blown. If the fuse blows again, call for service to check for a short circuit. * Verify the ice maker power switch is turned ON. * Address low voltage by adding a manostat. * Replace a damaged ice cube full sensor. * Remove some ice if the ice storage bin is full, and ensure the ice-full sensor is free of ice.
K
Kevin JohnsAug 20, 2025
What to do if my Maxx Ice Ice Maker stops suddenly while making ice?
- C
  caitlinmooreAug 20, 2025
  If your Maxx Ice Ice Maker stops suddenly while making ice, there are several possible reasons: * Check if the electricity is off and reconnect the power supply line. * If the room temperature is out of the stated range, cut off the electricity and allow the ice maker to stop working until the temperature returns within the specified range. * Replace the fuse if it is blown. * Add a manostat if the voltage of the power supply is low. * Remove any obstruction if the ventilation louvers are covered.
A
Amy HerreraAug 25, 2025
Why is water leaking from my Maxx Ice Ice Maker?
- M
  Matthew BriggsAug 26, 2025
  If water is leaking from your Maxx Ice Ice Maker, here are a few things to check: * A few water drops when you open the door to take out ice from ice storage bin is normal condensation. * If the water supply connection is leaking, tighten the fitting. * If the nut of the water drain hole is leaking, tighten the nut. * If the drainpipe connection is leaking, tighten the fitting.
T
Tammy RomeroAug 27, 2025
What to do if the water doesn't feed in after the Maxx Ice Ice Maker starts?
- H
  Heather LambertAug 28, 2025
  If water isn't feeding into your Maxx Ice Ice Maker after it starts, check the following: * Ensure the water supply tap is turned on. * Adjust the water supply pressure to be within the stated range. * If the water inlet valve is damaged, replace it. * Make sure the water supply pipe is properly connected; reconnect it if necessary.
N
Nicole DunnAug 30, 2025
Why is the body of my Maxx Ice Ice Maker electrified?
- J
  Joseph MullinsAug 30, 2025
  If the body of your Maxx Ice Ice Maker is electrified: * Ensure the grounding line is properly connected in the socket and that the socket meets the required electrical standard. * If the lines are creepage, adjust, reconnect, or replace them.
C
Chad GrantSep 1, 2025
Why are my Maxx Ice Ice Maker cubes partially formed or white at the bottom?
- P
  perezmarySep 1, 2025
  If the ice cubes from your Maxx Ice Ice Maker are partially formed or white at the bottom: * Check if the water supply pressure is below 14.5psi (0.1MPa), indicating not enough water in the water bin. * Clean the sprinkler if it is partially blocked. * Check the water quality to ensure the water line isn't blocked, causing insufficient sprinkler pressure.
L
Lisa WardSep 4, 2025
Why is harvesting ice difficult with my Maxx Ice Ice Maker?
- M
  Michael HowellSep 4, 2025
  If you're finding it difficult to harvest ice from your Maxx Ice Ice Maker: * Ensure the water supply tap is turned on. * Adjust the temperature if the ambient and water temperatures are too low.
T
Theresa MorganSep 6, 2025
Why are the ice cubes too big in my Maxx Ice Ice Maker?
- H
  harperalanSep 7, 2025
  If the ice cubes are too big in your Maxx Ice Ice Maker, adjust the temperature because the ambient temperature and water temperature may be too low.
R
rodney14Sep 9, 2025
What to do if the power indicated lamp is light, but the Maxx Ice Ice Maker doesn't operate?
- C
  Carla MeltonSep 9, 2025
  If the power indicated lamp is lit, but your Maxx Ice Ice Maker doesn't operate: * Replace the fuse, as it may be blown. * Remove some ice cubes if the ice storage bin is full, ensuring the ice-full sensor is free of ice.
W
Wesley LawrenceSep 12, 2025
Why do scales occur frequently inside my Maxx Ice Ice Maker?
- C
  Christopher RichardSep 12, 2025
  If scales occur frequently inside your Maxx Ice Ice Maker, it is likely due to the hardness of the water being too high. Use a water-softening device installed in front of the water inlet valve.

Summary

ICE MAKER SAFETY

IMPORTANT SAFEGUARDS

Electrical Connection

COMPONENT LOCATIONS

ICE MAKER INSTALLATION

Location Requirements

Specifies clearance, ventilation, and environmental conditions for unit placement.

Electrical Requirements

Details grounding, circuits, voltage, and circuit breaker requirements.

Leveling the Ice Maker

Instructions on how to adjust the unit's feet to ensure it is level.

Connecting the water line

Step-by-step guide for connecting the water supply to the ice maker.

Recommended grounding method

Explains the importance and method of proper grounding for the appliance.

Water Supply and Drain Connections

Connecting the drain line

Instructions for setting up the gravity drain system for the ice maker.

OPERATION

Final Check List before Operation

Operating Method

How the Machine Makes Ice

CLEANING AND MAINTENANCE

Condenser Cleaning

SPRINKLER HEAD CLEANING

Ice Making System Cleaning

Detailed procedure for cleaning the ice making system to remove scale.

Interior Cleaning

Exterior Cleaning

TROUBLESHOOTING

Before Calling for Service

Troubleshooting Guide

Maxx Ice MIM130 Specifications

General

Ice Storage Capacity	1.5 pounds
Ice Type	Bullet Ice
Dimensions	14.5 x 11 x 14 inches
Weight	24 pounds
Voltage	115V
Frequency	60Hz
Water Supply	Manual fill
Power Supply	115V/60Hz
Cooling Type	Air-cooled
Ice Production	28 pounds per day