What to do if Maxx Ice Ice Maker is leaking water?
If you notice water leaking from your Maxx Ice Ice Maker, it could be due to a few reasons. Some water falling when you open the door is normal condensation. However, check the water supply connection and tighten the fitting if it's leaking. Also, make sure the drain pipe isn't higher than the drain outlet; if it is, lower the drain pipe.
What to do if Maxx Ice MIM50-O Ice Maker stops while making ice?
If your Maxx Ice Ice Maker suddenly stops while making ice, first, ensure that electricity is on by reconnecting the power supply line. If the room temperature is outside the specified range, disconnect the ice maker until the temperature normalizes. Also, if the ice storage bin is full, remove some ice cubes and ensure the ice-full probe is free of ice.
Why Maxx Ice Ice Maker makes ice slowly?
If your Maxx Ice Ice Maker is producing ice but the bin isn't filling up, the condenser may be dirty and needs cleaning. Also, check the installation to ensure that the airflow to the ice maker isn't obstructed. High ambient and water temperatures, or proximity to a heat source, can also cause this issue, so verify the installation conditions.
What to do if Maxx Ice MIM50-O is not getting water?
If water isn't feeding into your Maxx Ice Ice Maker after it starts, check if the water supply tap is turned off and turn it on. Also, ensure the water supply pipe is properly connected; if not, reconnect it.
Why Maxx Ice MIM50-O Ice Maker produces cloudy ice?
If your Maxx Ice Ice Maker is producing partially formed cubes or ice that's white on the bottom, it could be due to insufficient water in the water trough. Check if the water supply pressure is below 15 psig. Also, the water supply or filter may be restricted. Finally, check for a water leak at the water trough.
How to fix water leaking from Maxx Ice Ice Maker storage bin?
If water is leaking from the ice storage bin of your Maxx Ice Ice Maker, it could be because the drainhole below the bin is blocked; remove the bin and clean the drainhole. Another cause could be a kinked drain hose or one that's improperly placed higher than the floor of the ice storage bin; ensure the drain hose allows unhindered water drainage.
Why Maxx Ice Ice Maker won't turn on?
Your Maxx Ice Ice Maker might not be operating because it's unplugged, so ensure it's properly plugged in. Also, a blown fuse could be the issue; replace it, but if it happens again, have a service technician check for a short circuit. The power button might be off, so switch it to the 'ON' position. Lastly, if the ice storage bin is full, remove some ice to free the ice-full probe.
Why is my Maxx Ice MIM50-O so noisy?
If your Maxx Ice Ice Maker is making excessive noise during operation, it might be because the feet are not leveled and locked. You should level and lock the feet. Please, refer to the Leveling the Ice Maker section.
How to prevent scaling in Maxx Ice Ice Maker?
If scaling occurs frequently inside your Maxx Ice Ice Maker, it's likely due to the high hardness level of the water. To resolve this, install a water-softening device in front of the water inlet.
What to do if Maxx Ice Ice Maker is electrified?
If the body of your Maxx Ice Ice Maker is electrified, the ground line might not be properly connected in the socket. Ensure you are using a socket that meets the grounding requirements.
Explains DANGER, WARNING, and CAUTION symbols used in the manual.
Lists essential precautions to reduce risks of fire, shock, and injury.
Details proper grounding, circuit, and outlet specifications to prevent electrical hazards.
Emphasizes correct connection to prevent hazards and ensure safety.
Lists technical data and explains the manual's intent for users.
Illustrates and labels the main components of the ice maker for easy reference.
Instructions for removing packaging materials and preparing the unit for first use.
Specifies necessary space around the unit for ventilation and access.
Details ideal ambient/water temperatures and required water pressure for operation.
Focuses on safe electrical connections and avoiding dangers.
Step-by-step guide to ensure the unit is properly leveled for optimal performance.
Details how to change the direction of the door opening.
Guide to connecting the water inlet with required tools and shut-off valve.
Instructions for connecting the drain outlet and ensuring proper flow.
Covers proper drain routing, air gaps, and leak checks.
Describes different ways the ice maker can be installed.
Essential checks before powering on the unit.
How to start the unit and the sequence of ice production.
Explains the two main phases of ice making: freezing and harvesting.
Describes water consumption and typical sounds heard during operation.
Steps to take when the ice maker will not be used for an extended period.
How to clean the outside surfaces of the ice maker.
Steps for cleaning the interior ice storage bin and the condenser.
Instructions for cleaning and clearing blockages in the water tube.
Comprehensive guide for cleaning mineral buildup and sanitizing the system.
Explains the purpose and operation of the control panel elements.
Step-by-step instructions for modifying ice cube dimensions.
Highlights automatic processes, sensors, and protection systems.
A table listing common problems, their causes, and recommended fixes.
Solutions for specific operational faults like noise, leaks, and scaling.
General| Type | Portable Ice Maker |
|---|---|
| Cooling Type | Air-Cooled |
| Production Capacity | 50 lbs per day |
| Ice Type | Bullet Ice |
| Power Supply | 115V, 60Hz |
To Next Page
