Maytag MDB8969SD - User Manual

To Next Page

PRODUCT DIMENSIONS

Undercounter Dishwasher

PRODUCT MODEL NUMBERS

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Page 1 of 2

If connecting dishwasher with a power supply cord:

Use power supply cord kit (Part

Number 4317824) marked for use

with dishwashers. Follow the kit

instructions for installing the power supply cord.

Power supply cord must plug into a grounded

3 prong outlet located in the cabinet next to the

dishwasher opening. Outlet must meet all local

codes and ordinances.

Water Supply Requirements: A hot water line with 20 to

120 psi (138 to 862 kPa) water pressure. Water temperature

must be 120°F (49°C) water at dishwasher. Use

" O.D.

copper tubing with compression fitting or flexible braided

water supply line.

Note: " minimum plastic tubing is not recommended.

Use a 90° elbow with " hose connection with rubber

washer (Part Number W10273460). Do not solder

within 6" (15.2 cm) from water inlet valve.

Drain Requirements:A new drain hose is supplied with

your dishwasher. If this is not long enough, use a new

drain hose with a maximum length of 12' (3.7 m) (Part

Number 3385556) that meets all current AHAM/IAPMO

test standards, is resistant to heat and detergent, and

fits the 1" (2.5 cm) drain connector of the dishwasher.

Make sure to connect the drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20" (50.8 cm)

minimum above the floor. It is recommended that the

drain hose either be looped

up and securely fastened to

the underside of the counter

or be connected to an air gap.

Make sure to use an air

gap

if the drain hose is

connected to house

plumbing lower than

20" (50.8 cm) above

subfloor or

floor.

Use

" (1.3 cm) minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance

with the air gap installation instructions. When connecting

the air gap, a rubber hose (not provided) will be needed

toconnect to the waste tee or disposer inlet.

air gap

B. For panel-ready models, dishwasher

depth is 24" (60 cm) not including the

" (1.9 cm) custom door panel.

C. Door handles may protrude forward

of the face of the dishwasher; varies

by model.

A. Insulation may be compressed

(not used on all models).

" -

4 "

(8.8 cm - 10.6 cm)

For 4" (10 cm)

toekick, height of

cabinet opening is

" (86.3 cm).

(62.2 cm)

(60.6 cm)

(1.9 cm)

(85,1 cm)

min. with

wheels

removed

(9.4 cm)

21 "

(53.3 cm)

30"

(76.2 cm)

MDB4949SD MDB6949SD

MDB5969SD MDB7949SD

Electrical Requirements:120-volt, 60 Hz, AC-only,

15- or 20-amp. fused electrical supply. Copper wire only.

A time delay fuse or circuit breaker and separate circuit

is recommended.

If direct wiring dishwasher: Use flexible, armored

or nonmetallic, sheathed copper

wire with grounding wire that

meets the wiring requirements for

your home and local codes and ordinances.

Use a UL Listed or CSA Approved conduit connector.

W10741197A-D-MT

12/2016

MDB8969SD MDB8959SF

MDB8979SE MDB8979SF

Need help?

Do you have a question about the Maytag MDB8969SD and is the answer not in the manual?

Summary

Electrical Requirements

Direct Wiring

Use flexible, armored, or nonmetallic copper wire with grounding.

Power Supply Cord Connection

Use a power supply cord kit plugged into a grounded 3-prong outlet.

Summary

Electrical Requirements

Direct Wiring

Use flexible, armored, or nonmetallic copper wire with grounding.

Power Supply Cord Connection

Use a power supply cord kit plugged into a grounded 3-prong outlet.

The Maytag Undercounter Dishwasher is designed for integration into kitchen cabinetry, offering efficient dish cleaning with various models available, including MDB4949SD, MDB5969SD, MDB6949SD, MDB7949SD, MDB8969SD, MDB8959SF, MDB8979SE, and MDB8979SF.

Function Description:

This appliance is an undercounter dishwasher intended for washing dishes. It requires specific electrical, water, and drain connections to operate correctly. The design allows for installation within standard kitchen cabinet cutouts, with options for direct wiring or power supply cord connection. The dishwasher is designed to fit snugly under a countertop, with dimensions carefully specified to ensure proper clearance and integration.

Important Technical Specifications:

Electrical Requirements:

Voltage: 120-volt
Frequency: 60 Hz
Current: AC-only, 15- or 20-amp. fused electrical supply
Wiring: Copper wire only. A time delay fuse or circuit breaker and a separate circuit are recommended.
Direct Wiring: Requires flexible, armored or nonmetallic, sheathed copper wire with a grounding wire that meets home and local codes and ordinances. A UL Listed or CSA Approved conduit connector must be used.
Power Supply Cord: If using a power supply cord, it must be Part Number 4317824, designed for dishwashers. The cord must plug into a grounded 3-prong outlet located in the cabinet next to the dishwasher opening, meeting all local codes and ordinances.

Water Supply Requirements:

Water Temperature: Hot water line with 120°F (49°C) water at the dishwasher.
Water Pressure: 20 to 120 psi (138 to 862 kPa).
Connection: Use 3/8" O.D. copper tubing with compression fitting or a flexible braided water supply line.
Note: ½" minimum plastic tubing is not recommended.
Elbow: A 90° elbow with a 3/4" hose connection and rubber washer (Part Number W10273460) is required.
Installation Precaution: Do not solder within 6" (15.2 cm) from the water inlet valve.

Drain Requirements:

Drain Hose: A new drain hose is supplied. If a longer hose is needed, use a new drain hose with a maximum length of 12' (3.7 m) (Part Number 3385556). This hose must meet all current AHAM/IAPMO test standards, be resistant to heat and detergent, and fit the 1" (2.5 cm) drain connector of the dishwasher.
Connection Point: The drain hose must connect to a waste tee or disposer inlet above the drain trap in the house plumbing and at least 20" (50.8 cm) minimum above the floor.
Air Gap: It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter or be connected to an air gap. An air gap must be used if the drain hose is connected to house plumbing lower than 20" (50.8 cm) above the subfloor or floor.
Drain Line Fittings: Use 1/2" (1.3 cm) minimum I.D. drain line fittings.
Air Gap Installation: If an air gap is required, it should be installed according to its installation instructions. When connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

Physical Dimensions (Approximate):

Overall Depth (excluding door panel for panel-ready models): 24½" (62.2 cm)
Overall Height (min. with wheels removed): 33½" (85.1 cm)
Overall Width: 237/8" (60.6 cm)
Toekick Height: 3½" - 4¼" (8.8 cm - 10.6 cm). For a 4" (10 cm) toekick, the height of the cabinet opening is 34½" (86.3 cm).
Door Panel Thickness (for panel-ready models): 3/4" (1.9 cm)
Door Handles: May protrude forward of the face of the dishwasher; varies by model.

Cabinet Cutout Dimensions:

Minimum Width: 24" (61 cm)
Minimum Depth: 24" (61 cm)
Minimum Height (D): 34" (86.4 cm) from the lowest point on the underside of the countertop. This can be reduced to 33½" (85.1 cm) by removing the rear leveling legs.
Utility Connections Area (Shaded): Areas on cabinet walls where utility connections can be installed.
Clearance: All surfaces must have no protrusions that would prohibit dishwasher installation.
Minimum Opening (E): Measured from the narrowest point of the opening.

Usage Features:

Integrated Design: Designed to seamlessly fit into kitchen cabinetry, providing a clean, built-in look.
Versatile Installation: Can be installed with either direct wiring or a power supply cord kit, offering flexibility based on existing electrical setups.
Hot Water Connection: Requires a dedicated hot water line to ensure optimal washing performance.
Proper Drainage: Emphasizes correct drain hose routing and connection to prevent issues and ensure efficient water removal. The option for an air gap provides an additional layer of protection against backflow.

Maintenance Features:

Durable Materials: Specifications for copper wiring and robust drain hoses (meeting AHAM/IAPMO standards) suggest a focus on longevity and resistance to common wear factors like heat and detergent.
Clearance for Service: The detailed dimensions and cutout requirements ensure adequate space for installation and potential future servicing.
Replaceable Parts: The mention of specific part numbers for the power supply cord kit and drain hose indicates that these components are designed to be replaceable if needed.