Maytag MDG-75 User Manual

Part No. 113065
MDG-75
Installation/Operator's Manual
For replacement parts, contact the distributor from which the dryer
was purchased or
MAYTAG
403 West Fourth Street North
Newton, Iowa 50208
(515) 792-7000
111898JEV/mt
WARNING: For your safety the
information in this manual must be
followed to minimize the risk of fire or
explosion or to prevent property damage,
personal injury or death.
Do not store or use gasoline or other flammable
vapor and liquids in the vicinity of this or any
other appliance.
WHAT DO YOU DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any electrical switch; do not use
any phone in your building.
* Clear the room, building or area of all
occupants.
* Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
* If you cannot reach your gas supplier, call the
fire department.
Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
AVERTISSEMENT: Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
dincendie ou dexplosion ou pour éviter tout
dommage matériel, toute blessure ou la mort.
Ne pas entreposer ni utiliser dessence ni
dautres vapeurs ou liquides inflammables dans
le voisinage de cet appareil ou de tout autre
appareil.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
* Ne pas tenter dallumer dappareil.
* Ne touchez à aucun interrupteur. Ne pas
vous servir des téléphones se trouvant dans
le bâtiment où vous vous trouvez..
* Évacuez la pièce, le bâtiment ou la zone.
* Appelez immédiatement votre fournisseur de
gaz depuis un voisin. Suivez les instructions
du fournisseur.
* Si vous ne pouvez rejoindre le fournisseur
de gaz, appelez le service des incendies.
Linstallation et lentretien doivent être assurés
par un installateur ou un service dentretien
qualifié ou par le fournisseur de gaz.

Maytag MDG-75 Specifications

General

Brand	Maytag
Model	MDG-75
Category	Dryer
Language	English

Summary

Important Information

Receiving and Handling

Procedures for inspecting, accepting, or refusing dryers damaged during shipment.

Safety Precautions

Critical safety warnings and guidelines for operating the dryer safely.

Specifications and Component Identification

Specifications

Technical details and measurements of the dryer, including capacity, dimensions, and power.

Component Identification

Identification of major dryer components through diagrams and labels.

Installation Procedures

Location Requirements

Guidelines for selecting a suitable installation location, considering codes and clearances.

Unpacking and Setting Up

Steps for removing the dryer from its packaging and initial setup.

Dryer Enclosure Requirements

Specifies clearances and construction requirements for dryer enclosures.

Fresh Air Supply

Details on providing adequate make-up air for dryer operation and efficiency.

Exhaust Requirements

Guidelines for designing and installing exhaust ductwork for safe and efficient venting.

Electrical Information

Requirements and safety precautions for electrical connections and wiring.

Gas Information

Guidelines for gas supply connections, pressure, and safety.

Preparation for Operation and Start-Up

Checklist of items to verify before operating the dryer for the first time.

Preoperational Tests

Procedures for performing functional checks before the dryer is put into use.

Preoperational Instructions

Steps for starting the dryer, covering both microprocessor and dual timer models.

Shut Down Instructions

Procedures for safely shutting down the dryer for a period of time.

Service and Parts Information

Service

Information on obtaining qualified service and contacting Maytag.

Parts

Guidance on purchasing replacement parts and providing necessary information.

Warranty Information

Returning Warranty Card(s)

Instructions on warranty registration and obtaining warranty information.

Routine Maintenance

Cleaning

Schedule and procedures for cleaning the dryer and exhaust system to prevent fire hazards.

Adjustments

Recommended checks and adjustments for belts, connections, and safety devices.

Functional Check of Replacement Components

Microprocessor (Computer) Board Check

Steps to check the functionality of a replacement microprocessor board.

Hot Surface Ignition (HSI) System Check

Procedure for checking the hot surface ignition system on gas models.

Reversing Timer Spin and Dwell Adjustments

Technical Information

Data Label

Explanation of the information contained on the dryer's data label.

Troubleshooting

Troubleshooting Microprocessor Models

Troubleshooting guide for issues specific to microprocessor-controlled dryers.

Troubleshooting Timer Models

Troubleshooting guide for issues specific to timer-controlled dryers.