To Next PageTo Next Page
Need help?Do you have a question about the Maytag MFS55 and is the answer not in the manual?
General| Brand | Maytag |
|---|---|
| Model | MFS55 |
| Capacity | 5.5 cu. ft. |
| Color | White |
| Voltage | 120 V |
| Type | Top Load |
| Agitator | Yes |
| Width | 27.5 inches |
Provides critical warnings to reduce risks of fire, electric shock, or injury during washer use.
Lists necessary tools, additional materials, and parts supplied for washer installation.
Details ideal placement, environmental conditions, and necessary utilities for washer installation.
Information on available optional equipment, such as the steam heater kit for specific models.
Guidelines for mounting washers on elevated metal bases or cement slabs.
Instructions for securing washers on concrete floors or pads with anchor bolts.
Details for installing MFS18 and MFS25 models on elevated pads without bolts.
Fabrication details for metal bases used for secured washer installations.
Construction specifics for metal bases used in freestanding installations of MFS18/MFS25.
Diagram and dimensions for correctly placing anchor bolts for washer installation.
Emphasizes the user's responsibility for ensuring adequate electrical connections per codes.
Details direct wiring, power supply cable requirements, and conductor gauges for washer connection.
Explains connecting washers to each other and to a protective conductor for grounding.
Specifies required water pressure, temperature, and connection types for optimal washer operation.
Outlines requirements for drain pipe diameter, waste channel, and air gap for proper drainage.
Information on connecting external liquid laundry product pumps to PN and PD model washers.
Procedures for inspecting the washer upon arrival and guidelines for proper storage.
General steps for moving and positioning the washer before securing it.
Detailed steps for securing the washer to a concrete floor or pad using anchor bolts.
Instructions for leveling and securing the washer on a base without anchor bolts.
Steps for removing shipping brackets and replacing panels after initial setup.
Critical warnings to disconnect power before servicing to prevent shock.
Steps for connecting the water supply hoses, including flushing lines and checking fittings.
Instructions for cutting and attaching the drain hose to ensure proper drainage.
Guidance on connecting laundry product supply pumps for PN and PD models.
Details on connecting relay leads for PN and PD models, including wiring diagrams.
Information on tubing connectors, drilling them out, and attaching hoses for chemical dispensing.
Additional steps for PD models to connect tubing to dispenser box connectors.
Final checks and procedures after initial installation, including leveling and power connection.
Recommended checks and adjustments to be performed after 24 and 80 operation hours.
Reference to a guide for programming and controls troubleshooting.
Lists routine maintenance tasks to be performed after each load, daily, and at specific hour intervals.
Explains the function of the vibration switch and how to adjust and test it.
Warnings to disconnect power before performing maintenance to avoid electrical shock.
Procedures for inspecting, adjusting, and replacing the washer belts for optimal performance.
Steps for adjusting or replacing the door seal to prevent water leaks.
Detailed steps for replacing the washer belts, including motor adjustments.
Specific instructions for adjusting the door seal pressure on MFS18/MFS25 models.
Specific instructions for adjusting the door seal pressure on MFS35/MFS55 models.
Steps for removing the door glass and replacing the rubber door seal gasket.
Information on the location and replacement of in-line fuses for the washer.
Instructions on how to open the washer door manually in case of a power failure.
Comprehensive table detailing various dimensions for all washer models.
Diagram showing component locations on the front of MFS18 and MFS25 models.
Diagram showing component locations on the front of MFS35 and MFS55 models.
Diagram illustrating the location of components on the top of the washer.
Diagram showing the location of components on the back of the washer.
Detailed table of dimensions, net weight, package dimensions, and gross weight for all models.
Specifications for supply voltage, fuse/breaker type, and GFCI requirements.
Details on allowable and recommended water pressure, inlet type, and maximum temperature.
Specifications for drain diameter and flow rate for proper wastewater discharge.
Operating temperature, humidity, elevation, and storage temperature limits.
Specifications for static and dynamic loads, and dynamic frequency for floor support.
Information on noise output levels for the washers.
Specifications for low and high-pressure steam connections.
Recommended torque values for steel bolts used in installation and maintenance.
