Maytag MGR5755QD User Manual (English)

Other manuals for Maytag MGR5755QD

Service Manual42 pages

Installation Manual21 pages

Questions and Answers:

L
Laura FarleySep 6, 2025
How to troubleshoot spark issues on Maytag Ranges ignitor?
- G
  gerald18Sep 6, 2025
  If you have no spark or only a random spark at one ignitor on your Maytag range, replace the ignitor lead or electrode if you find a cracked ignitor or pinched ignitor wire. Then, clean the burner cap and lead to ensure good continuity. Tighten the ground connection and fix any breaks in the ground path from the ignitor to the unit ground. Finally, replace the ignitor lead if it's cracked or broken.
A
adayAug 23, 2025
What to do if my Maytag MGR5755QD oven door will not unlock?
- C
  Crystal RayAug 25, 2025
  If the oven door on your Maytag range will not unlock, allow the self-cleaning cycle to complete. If the oven is still hot, the door will not unlock until it has cooled to a safe temperature. Do not force the door open, as this will void the warranty. You can blow cool air on the door latch area to quicken the cooling process.
S
Spencer FergusonAug 25, 2025
What to do if the oven door will not unlock after self-clean cycle on my Maytag MGR5755QD?
- E
  Ellen WyattAug 26, 2025
  If your Maytag Ranges' oven door won't unlock after a self-clean cycle, allow approximately one hour for the oven to cool down completely. The control and door might also be locked.
W
William FrostAug 26, 2025
How to reset the self-clean cycle on a Maytag MGR5755QD?
- V
  Virginia ButlerAug 27, 2025
  If the self-clean cycle is not working on your Maytag range, shut off power to the oven for five minutes by switching off the circuit breaker. Then, reset the circuit breaker and try the oven again.
M
Melissa BakerAug 27, 2025
How to fix a Maytag Ranges surface burner that fails to light?
- R
  Renee DeleonAug 27, 2025
  If the surface burner on your Maytag Ranges fails to light, ensure the unit is properly connected to the power supply. Check for a blown circuit fuse or a tripped main circuit breaker. Confirm that the ignitor is dry and clicking. The burner will not light if the ignitor is damaged, soiled, or wet. If the ignitor doesn’t click, turn the control knob OFF.
C
christopher68Aug 28, 2025
Why is there a strong odor or light smoke when my Maytag MGR5755QD oven is turned on?
- C
  Cody RamirezAug 28, 2025
  If you notice a strong odor or light smoke when you turn on your Maytag Ranges oven, this is normal for a new range and should disappear after a few uses. Initiating a clean cycle can help burn off the odors more quickly. Turning on a ventilation fan will also help remove the smoke or odor. Excessive food soils on the oven bottom may also cause this.
J
Julie SmithSep 12, 2025
Why does my Maytag MGR5755QD smoke when I first use it?
- S
  swhitakerSep 12, 2025
  Minor smoking and/or odor is normal the first few times you use your Maytag range oven.
M
millermichaelSep 14, 2025
Why my Maytag MGR5755QD Ranges oven will not self-clean?
- V
  velezjoshuaSep 14, 2025
  If your Maytag Ranges oven isn't self-cleaning, ensure the cycle isn't set for a delayed start. Also, check that the door is fully closed and that the control is not in Sabbath Mode. The oven temperature may be over 400°F.
K
Katie ChapmanSep 5, 2025
What to do if gas flows to my Maytag Ranges burner but it doesn't light?
- M
  Margaret AcevedoSep 5, 2025
  If gas is flowing to the bake/broil burner but it's not lighting on your Maytag range, reposition the ignitor closer to the burner. Also, clean any dirt or grease from the orifice or burner. Check for correct gas pressure (4" WCP for natural gas and 10" WCP for LP gas). Finally, verify that there isn't a power outage and that the circuit breaker hasn't tripped.
A
Amanda FletcherSep 2, 2025
Why won't my Maytag MGR5755QD burners ignite?
- N
  Natasha RobinsonSep 3, 2025
  If the burners on your Maytag range won't ignite and there's no spark, start by cleaning the burner cap to ensure a good ground. If that doesn't work, the spark module might be weak or faulty and require replacement. Also, verify that the gas pressure is correct: 4” WCP for natural gas and 10” WCP for LP gas.