Maytag MHW5630HW User Manual (English)

Other manuals for Maytag MHW5630HW

Installation Instructions76 pages

Guide11 pages

Quick Reference Guide2 pages

Use And Care Guide57 pages

Questions and Answers:

E
Emily DiazAug 20, 2025
Why is my Maytag Dryer not running?
- W
  wwilliamsAug 20, 2025
  Your Maytag Dryer might not be running due to several reasons. First, ensure the dryer door is completely closed. Also, touch and hold the START/PAUSE button until the display counts down "3-2-1" and the dryer starts. Check your household fuses or circuit breakers, as there may be two dedicated to the dryer. Ensure both fuses are intact and tight, and that the circuit breakers haven't tripped; replace fuses or reset the breakers if needed. Electric dryers need a 240-volt power supply, so verify this with a qualified electrician. Finally, make sure you are using a time-delay fuse.
T
torresconnorAug 22, 2025
What to do if my Maytag Dryer will not run?
- J
  johnnytylerAug 22, 2025
  If your Maytag Dryer isn't running, here's what you can check: * Make sure the door is fully closed. * Touch and hold the START/PAUSE button until the display shows the countdown and the dryer starts. * Inspect the household fuses or circuit breakers (there may be two for the dryer) and replace/reset if necessary. If the problem continues, call an electrician. * Confirm that your electric dryer has a 240-volt power supply by consulting a qualified electrician. * Verify you're using a time-delay fuse.
K
Karen HamiltonAug 25, 2025
How to fix Sd or Sud error on Maytag MHW5630HW?
- E
  elizabethadamsAug 25, 2025
  If the Sd or Sud error code appears on the display of your Maytag Washer, it means there are excessive suds in the washer, and it is running a suds-reduction routine. Allow the washer to continue. Make sure you are only using HE detergent and follow the detergent manufacturer’s instructions to determine the correct amount based on load size. Consider using a different HE detergent.
M
Mary Williamson DVMAug 26, 2025
What to do if Maytag Washer door will not lock?
- D
  darin32Aug 26, 2025
  The F5 E2 or F05 E02 error code on your Maytag Washer means the door will not lock. Touch POWER to cancel the cycle. Ensure that the door is completely closed and latched. Check for any items in the washer drum that may be preventing the door from closing properly.
B
barrettchristineAug 27, 2025
Why is my Maytag MHW5630HW leaking water?
- P
  Paul LawsonAug 28, 2025
  If water or suds are leaking from the door or rear of your Maytag Washer, it could be due to using non-HE detergent or using too much HE detergent. Only use HE detergent. Suds from regular detergents can cause leaking. If you're running the Clean Washer with affresh® cycle, avoid using thickened, easy-pour, or no-splash bleach. Use affresh® tablet or regular, non-thickened chlorine bleach. Periodically clean the underside of the glass window to avoid potential leaks. Water can drip off the inside of the door if opened during Add Garment.
N
Nicholas EdwardsAug 29, 2025
Why is my Maytag MHW5630HW leaking around the door?
- S
  Sean MillerAug 29, 2025
  If your Maytag Washer is leaking around the door, it may be due to hair, lint, or other debris on the inner door glass, preventing a proper seal with the rubber door seal. Clean the inner door glass and seal to ensure a tight closure.
P
Peter WilsonAug 31, 2025
How to fix a Maytag Dryer that won't start?
- S
  Samantha RichardsAug 31, 2025
  To fix a Maytag Dryer that won't start, begin by ensuring the door is completely closed. Then, touch and hold the START/PAUSE button until the display counts down "3-2-1". Check the household fuses or circuit breakers; replace any blown fuses or reset tripped breakers. Electric dryers need a 240 volt power supply, so consult with a qualified electrician to verify. Also, ensure you are using a time-delay fuse.
J
Jennifer LeeSep 2, 2025
How to fix F9 E1 error on Maytag Washer?
- D
  Deborah ChandlerSep 2, 2025
  The error code F9 E1 or F09 E01 on your Maytag Washer indicates a drain pump system error. Ensure the top of the drain pipe is at least 39 inches above the floor and the drain hose extends no farther than 4.5 inches into the standpipe. Also, ensure the drain hose is not kinked, pinched, or blocked. If it is clogged, remove any clogs. Using only HE detergent can also solve the problem. Always measure detergent and follow manufacturer’s directions based on load size and soil level.
J
jared04Sep 3, 2025
What to do if Lo FL error appears on my Maytag MHW5630HW Washer?
- J
  jsimpsonSep 3, 2025
  The error code Lo FL, F8 E1, or F08 E01 on your Maytag Washer indicates a water supply error. The unit will drain for 8 minutes while the door remains locked. The drain cycle must be allowed to complete or the error code cannot reset. When complete, touch POWER once to clear the code, then touch POWER again and restart the washer. Ensure both inlet hoses are properly attached to the inlet valve, both hot and cold water faucets are turned ON, and the inlet valve screens on the washer are not clogged. Remove any kinks in the inlet hose. Auto shut-off connectors and hoses must be properly installed and in working order.
M
Michael JonesSep 5, 2025
How to fix F0 E5 error on Maytag MHW5630HW?
- H
  Hunter GreenSep 5, 2025
  If you see 'F0 E5' or 'ob' on your Maytag Washer display, it means an off-balance load has been detected. To resolve this, touch POWER once to clear the code, then touch POWER again to restart the washer.

Maytag MHW5630HW Specifications

General

Style	Front-Loading
Color	Metallic Slate
Washer Capacity	4.5 cu ft
Dryer Capactity	-
Max Spin Speed	1160 RPM
Spin Speeds	Medium
Spin Class	C
Number of Cycles	10
Cycle Selections	Wool
Wash	Normal
Options	Delay start time
Hours	Delay Wash
Noise level	-
Temperature Selections	Eco warm
Energy Class	-
Annual Energy Consumption	-
Annual Water Consumption	-
Water Consumption Per Cycle	-
Voltage	120V
Frequency	60 Hz
Current	15-20 A