EasyManua.ls Logo

MB QUART FORMULA FX1.400 - User Manual

MB QUART FORMULA FX1.400
11 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
System Design
The success of any car stereo system relies on several factors, such as
the system design, execution of the installation, and system setup. Please
remember that any system is only as good as its weakest link.
Please remember that higher power systems are not necessarily useful
purely for high sound pressure levels, but also to establish a headroom
capability, to reproduce musical peaks cleanly without distortion.
Lower power amplifiers will clip earlier than their more powerful cousins,
and cause loudspeaker failure when overdriven, due to the harmonics
generated by a clipped signal, thus overheating voice coils.
Amplifiers should be mounted with the fins running horizontally for best
convection cooling, to minimize overheating. Purchase the best quality
RCA cables you can afford, for reliability and less engine noise
interference in the audio system.
It is highly recommended that the amplifier be mounted to a board of MDF
or other solid structure using the 4 mounting screws provided. Avoid
mounting the amplifier to metal as this can introduce noise and other
unwanted issues. When mounting the amplifier, ensure that it is mounted
HORIZONTALLY, as shown in the diagram above, for optimal heat
dissipation. Mounting amplifiers to speaker enclosures is not
recommended as this can cause damage to the amplifier components.
When choosing a location for mounting the amplifier, ensure that you
check for clearance from wires, gas tank, electrical devices and brake
lines etc.
Congratulations!
By purchasing an amplifier from MB Quart, you have decided on a product
of the highest technical quality. MB Quart wishes you great enjoyment with
your amplifier. Should you have any questions about this system or other
MB Quart products, please email us at info@maxxsonics.com
Installation Manual
WOOD
FORMULA
www.mbquart.com
FX2.60 / FX4.50 / FX4.70 / FX4.100 / FX1.400 / FX1.600

Questions and Answers

  • L
    Laura FisherAug 12, 2025
    What to do if my MB QUART FORMULA FX1.400 Car Amplifier system does not turn on?
    • R
      Rachel GomezAug 13, 2025
      If your MB QUART Car Amplifier system doesn't turn on, begin by checking all fuses and connections. Also, measure the +12 volt and remote turn on voltages at the amplifier terminals.
  • C
    Christina SweeneyAug 16, 2025
    Why is my MB QUART FORMULA FX1.400 overheating?
    • E
      Eddie JacksonAug 16, 2025
      Your MB QUART Car Amplifier might be overheating due to inadequate cooling. Relocate or remount it to allow better airflow. Another cause may be driving high power levels into low impedances. Try reducing the volume or ensuring the loudspeaker impedance meets the recommended specifications.
  • J
    justin99Aug 20, 2025
    What causes low output power in my MB QUART Car Amplifier?
    • J
      Jeanette BryantAug 20, 2025
      Low output power in your MB QUART Car Amplifier can be caused by improperly set level controls. Ensure they are correctly configured. Also, check that the battery voltage at the amplifier’s terminals is at least 11 volts. Inspect all +12 volt and ground connections as well.
  • A
    Amber NelsonAug 25, 2025
    Why does my MB QUART Car Amplifier keep blowing fuses?
    • C
      Christopher OwenAug 25, 2025
      Your MB QUART Car Amplifier might be blowing fuses due to using loudspeaker impedances below the recommended minimums. Also, a short on the main +12 volt cable from the battery to the vehicle chassis will cause the main fuse to blow.
  • C
    chambersjasmineAug 27, 2025
    What to do if MB QUART FORMULA FX1.400 goes into diagnostic mode?
    • D
      david44Aug 27, 2025
      If your MB QUART Car Amplifier goes into diagnostic mode, try these steps: 1. Disconnect all RCA and speaker leads, leaving the +12 volt, power ground, and remote leads connected. 2. Turn the amplifier back on. If the diagnostic LED lights up, it indicates an internal fault. 3. Plug the RCA cables back in and reset the amplifier to check for input faults. 4. Connect the speakers one at a time to identify any faulty speakers or wiring.
  • L
    Laura HudsonAug 31, 2025
    How to eliminate a ticking or whine that changes with engine RPM in my MB QUART FORMULA FX1.400?
    • J
      Jose FoxAug 31, 2025
      To eliminate a ticking or whine that changes with engine RPM in your MB QUART Car Amplifier: * Relocate RCA cables that may be too close to a fuel pump or distributor. * Check that the head unit ground is connected directly to the vehicle chassis, not using factory wiring. * Try supplying the head unit with a clean +12 volt supply directly from the battery +, instead of using a supply from the in dash wiring/fusebox.
  • M
    michael79Sep 4, 2025
    How to get rid of hiss or white noise from MB QUART Car Amplifier?
    • M
      Martha KelleySep 4, 2025
      To reduce hiss or white noise from your MB QUART Car Amplifier, readjust the amplifier level controls, following the setup procedures. If the issue persists, unplug the amplifier input RCA cables; if the hiss reduces, the source unit is likely the cause.
  • J
    Jacqueline HansonSep 8, 2025
    How do I fix a constant whine in my MB QUART FORMULA FX1.400 system?
    • R
      Ryan WashingtonSep 8, 2025
      To fix a constant whine in your MB QUART Car Amplifier system, check all connections, paying special attention to ensure good grounds. Also, make sure that no speaker leads are shorting to exposed metal on the vehicle chassis.

Summary

Introduction and System Design

Congratulations

Welcome message and encouragement for purchasing an MB Quart amplifier.

System Design and Installation Principles

Key factors for successful car stereo system design, mounting, and wiring.

Warranty Information

MB Quart Amplifier Warranty Terms and Exclusions

Details warranty coverage, exclusions, and claim requirements.

Installation Instructions

General Installation and Wiring Guidelines

Guidelines for wiring, power/ground connections, and safe installation practices.

System Power-Up Procedure

Recommended steps for safely powering up the audio system for the first time.

Settings for Best Performance

Amplifier Control Settings

Guidance on setting High Pass, Low Pass, Bass EQ, Subsonic, and Level controls.

Troubleshooting Common Issues

Diagnostic System and Protect LED

Explanation of the amplifier's diagnostic system and the PROTECT LED indicator.

Troubleshooting Common Problems

Solutions for overheating, low power, fuse issues, no power, and noise problems.

Product Series Overview

FX2.60 2-Channel Amplifier

Features, controls, and configurations for the FX2.60 2-channel amplifier.

FX4.50;FX4.70;FX4.100 4-Channel Amplifiers

Features, controls, and configurations for 4-channel amplifiers.

FX1.400;FX1.600 Mono Amplifiers

Features, controls, and configurations for mono amplifiers.

Technical Data and Specifications

Amplifier Performance Specifications

Key performance metrics including power, electrical specs, and protection features.

Amplifier Connectivity and Fusing

Details on connector types, fusing requirements, and physical dimensions.

OEM Integration Accessories

MX-1;MX-2 High To Low Level Converters

Features of MX-1 and MX-2 converters for integrating OEM speakers.

MX-3 Bass Controller & MX-4 Sub Add-On

Features of MX-3 Bass Controller and MX-4 Sub Add-On accessories.

MB QUART FORMULA FX1.400 Specifications

General IconGeneral
BrandMB QUART
ModelFORMULA FX1.400
CategoryCar Amplifier
LanguageEnglish

Related product manuals