Instructions for use
First time use
Blender is delivered only partially charged and needs to be charged fully before use. Charge
for up to three hours until charging status light (power button) is green while charging.
Clean blender blade assembly (be careful of sharp blades), jar and travel lid with soap and
water prior to first use.
Typical use
Place liquid into jar at least to minimum fill line. Add any additional ingredient items.
When blending ice, use standard size refrigerator ice cubes or bagged ice. Bagged ice
should be broken down to individual cubes; do not place large chunks of ice in jar. Blender
can handle jar being approximately half filled with ice.
Place blade assembly on top of jar, turn blade assembly clockwise until firmly closed.
When closed, turn over assembled jar and insert into motor base. Align jar engagement
tab with motor base engagement slot, push down into slot and turn clockwise into locked
position. Note: if bottom of blade assembly will not sit down into slot easily, turn
With blender on sturdy stable surface, press and hold power button. Release power button
to shut off blender.
Typical recipes will require pulsing. Hold power button on for approximately 5 seconds,
then release power button. Repeat pulsing in this manner until desired consistency.
When blending is complete, turn jar counter clockwise and then liſt jar up away from motor
base when engagement tab aligns with engagement slot.
Turn jar over and remove blender blade assembly. Replace with travel lid
, or pour directly
into glass and enjoy.
Battery Charging
CHARGING – plug charger into electrical receptacle and charger port. Battery charging
takes 3.5 hours. Note blender will not work while charging, this is a built in safety feature
related to the lithium battery.
BATTERY STATUS INDICATORS – the blender power button is backlit with green, red and
flashing red colors
GREEN – greater than 90% charged
RED – greater than 25% charged
FLASHING RED – less than 25% charged
gear/teeth on bottom of blade assembly slightly and then try again.
06
Cleaning
Blade and jar assembly and travel lid can be cleaned with dish soap and water. Do not
submerge blade assembly under water, as bearings may be impacted. Rinse and allow
to dry thoroughly. Be careful with blades as they are sharp.
Jar, travel lid and blade cover are dishwasher safe. Blade assembly is not dishwasher safe.
Motor base should not be submerged or placed under running water, this will damage the
motor and battery components. Motor base can be cleaned with damp cloth.
Travel and Storage
Once all parts are completely dry, blender may be stored in bag. It is important all parts
are completely dry.
When using bag, blender jar should not be engaged into
motor base as accidental operation
may occur. Place motor base in bag without jar assembly engaged. Ensure motor base is
not stored such that power button may be pressed.
Blender is powered by a high quality, ETL certified lithium battery. As such blender should
not be stored for long periods without being charged as this may reduce battery life and
performance. Do not store for longer than 2 months without charging battery.
Warranty
All components of the blender are guaranteed for a period of 2 years from purchase
against manufacturing defects.
Troubleshooting
Possible reason blender will not operate when power button is pressed:
· Battery is not charged. Charge blender until power button turns green.
· Engagement tab is not locked into engagement slot. Follow instruction for proper jar
placement into motor base. This is a safety feature
· Thermal overload – the battery and motor components have built in overload protection.
If overload protection is activated, let blender rest (not plugged in to charger) for 30
minutes. Then plug into charger to charge prior to using again. This is a safety feature.
· Overheating – similar to other lithium battery powered devices, if the blender becomes
very hot due to ambient tempera
tures, extended exposure to hot sunlight, and/or
extensive use, overheat protection may be activated and blender will not work. Move
blender to lower temperature area and allow to cool for 30 minutes.
· Blender is plugged into charger – as another safety feature for the high powered
lithium battery contained in this product, the blender will not work while it is
connected to the charger.
Assembled blender jar engagement tab will not sit down into motor base engagement
slot – teeth on bottom of blade assembly are mis-aligned with groove on motor base.
Simply turn gear/teeth on bottom of blade assembly and try again.
07
To Next Page
Loading...