McCall 7-7020FT - User Manual

To Next Page

McCall Refrigeration / 81 West Holly Street / Parsons, TN 38363

Phone (731) 847-5570 / Fax (731) 847-9012 / 1-888-REACH-IN (1-888-732-2446) / www.mccallrefrigeration.com

January 2007 / Printed in U.S.A.

Model 7-7020FT, 7-7045FT, 7-7070F

Cabinet exterior: heavy gauge anodized aluminum. Stainless

steel door and hatch cover.

Cabinet interior: mill finish aluminum.

Standard Features

• Top mounted compressor and evaporator coil

• Hot gas condensate evaporator

• Automatic defrost.

• Cord and plug attached

• Master power switch.

• Windrunner gradient air displacement process

• R-404A refrigerant

• Automatic interior light.

• Dial Thermometer.

• Adjustable doorstops

Cabinet - Cabinets are all metal, inside and out.

The top, back, and bottom are made of galvanized

steel. In addition, all seams are closed and sealed,

with metal edges turned away from the exposed

surface. The result is an integrated structural

frame. Internal corners are coved to conform to

NSF standards. Automatic interior lighting is

controlled by a light switch concealed in the door

hinge. The cabinet is supported on four 6 inch

adjustable steel legs.

Doors - Constructed of metal, refrigerator doors

are self-closing and fully insulated. Their cam-lift

hinges are epoxy-coated and self-lubricating.

Hinges also have a safety stop that holds the door

open, preventing overswing. Chrome-plated pull

handles have built-in cylinder locks. The full-

perimeter, magnetic vinyl gaskets are removable

without the use of tools. Doors easily lift off,

and door perimeters have a built-in, low wattage,

and anti-condensate heater. Door openings are

protected by an impact-resistant, nonconductive

PVC breaker strip with no exposed screws

or fasteners.

Insulation - Cabinet body, doors, and evaporator

coil housings are filled with pressure-injected

polyurethane foam.

Interior Shelves - Three wire shelves are standard

per section. Shelves have a runner spaced 3/4 inch

O.C. with two reinforcing bars 8 1/2 inch O.C.

coated with 7 mils of baked-on gray epoxy. The

shelves have a saline spray corrosion resistance of

600 hours. Shelves will support 250 pounds each.

They are supported on stainless steel pilasters

(1000 series) & aluminum pilasters (2000-4000

series), and are adjustable on 1 inch centers. All

shelves are interchangeable and can be adjusted

without tools or special parts.

Self-Contained Refrigeration - The complete

refrigeration assembly is mounted on top of the

cabinet behind a removable hatch cover.

Refrigeration components include a hermetically

sealed compressor, 1 & 2 section have cap tube

(3-section uses expansion valve), thermostatic

temperature control, high-humidity evaporator

coil and hot gas condensate evaporator. The

system is balanced to maintain 0°F average

internal air temperature. Windrunner gradient air

displacement process provides even air flow and

temperature control throughout the cabinet. All

components are factory installed and tested, and

supplied with an attached cord and plug, master

switch, and interior thermometer.

7000 S

ERIES

EACH

-I

REEZERS

Approval :

SPECIFICATIONS

McCall Refrigeration specification sheets are available

online @ www.mccallrefrigeration.com

AIA #

ITEM #

MODEL #

PROJECT NAME

SIS #

7-7070F

7-7045FT

7-7020FT

CLASSIFIED TO

NSF (STD-7-1999)

Need help?

Do you have a question about the McCall 7-7020FT and is the answer not in the manual?

Summary

7000 Series Reach-In Freezers

Model Identification and Construction

Details the specific models (7-7020FT, 7-7045FT, 7-7070F) and their exterior/interior construction materials.

Standard Features List

Lists key operational features such as top-mounted compressor, automatic defrost, interior lighting, and dial thermometer.

Specifications Details

Cabinet Construction

Describes the integrated structural frame, sealed seams, and coved internal corners conforming to NSF standards.

Door Construction and Features

Details self-closing, insulated doors with cam-lift hinges, safety stop, chrome handles, and anti-condensate heaters.

Insulation Type

Specifies the use of pressure-injected polyurethane foam for cabinet body, doors, and evaporator coil housings.

Interior Shelving System

Describes three wire shelves per section, their epoxy coating, corrosion resistance, and adjustable pilaster support.

Self-Contained Refrigeration Assembly

Details the top-mounted refrigeration unit, components, temperature control, and air displacement process.

Electrical and Dimensional Data

Electrical Specifications by Section

Provides compressor HP, voltage, amperage, BTU/HR, and cord connection for one, two, and three-section models.

Dimensional Measurements

Lists net capacity, width, height, depth, net door opening, and adjustable shelf count for each model section.

Options and Bidding

Available Options

Lists optional features like heavy-duty casters, left/right door hinges, tray slides, and extra epoxy coated shelves.

Bidding Specification Requirements

Outlines requirements for materials like stainless steel, aluminum interior, and specific hardware for bidding purposes.

McCall 7-7020FT Specifications

General

Brand	McCall
Model	7-7020FT
Category	Freezer
Language	English