McIntosh MTI100 - FCC Information (For US Customers); IMPORTANT NOTICE: DO NOT MODIFY; CAUTION; COMPLIANCE INFORMATION

2
PERFORMANCE SPECIFICATIONS
Amplier
Power Output
50 watts into 8 ohm loads
80 watts into 4 ohm loads
Output Load Impedance
8 ohms or 4 ohms
Rated Power Band
20Hz to 20kHz
Total Harmonic Distortion
0.2% maximum harmonic distortion at any
level from 250 milliwatts to one-half of
rated power output, 20Hz to 20kHz
0.5% maximum harmonic distortion at
any level from one-half to full rated power
output, 20Hz to 20kHz
Dynamic Headroom
1dB 8 ohm load
1.3dB 4 ohm load
Frequency Response
+0, -0.7dB from 20Hz to 20kHz
Input Sensitivity (for rated output)
1.5V PWR Amplier IN
A-Weighted Signal to Noise Ratio
93dB (110dB below rated output) PWR
Amplier IN
Intermodulation Distortion
0.1% maximum if instantaneous peak
power output does not exceed the rated
output for anycombination of frequencies
from 20Hz to 20kHz
Wide Damping Factor
Greater than 200, 8 ohm load
Greater than 100, 4 ohm load
Input Impedance
6.5K ohms
Voltage gain
22dB
Preamplier
Frequency Response
+0, -0.7dB from 20Hz to 20,000Hz
Total Harmonic Distortion
0.2% from 20Hz to 20,000Hz
Rated Output (Main)
1.5V
Maximum Voltage Output
9V RMS
Sensitivity (for rated output)
High Level, 300mV AUX Input
Signal To Noise Ratio (A-Weighted)
High Level, 90dB
Phono, 75dB
Input Impedance
68K ohms AUX Input
Preamplier (cont’d)
Maximum Input Signal
4V AUX Input
Phono MM, 45mV
Voltage Gain
AUX Input to Main Output: 14dB
Phono MM Section: 40dB
Output Impedance
100 ohms
Headphone Load Impedance
100 ohms to 600 ohms
Digital Input Sample Rates
Optical: 16Bit, 24Bit - 32kHz to 192kHz
Coaxial: 16Bit, 24Bit - 32kHz to 192kHz
Bluetooth Proles
A2DP, AVRCP, SBC, HD, BT 4.2
TRIGGER OUTPUT
12VDC, 50mA maximum
Olympia Cartridge
Cartridge Type
Moving Magnet (MM)
Frequency Response
12Hz-30kHz
Output Voltage/Channel
4mV @ 1kHz
Channel Separation
30dB @ 1kHz
Channel Balance
1.5dB/1kHz
Compliance
12x10-6 cm/dyn @ 100Hz
Stylus Size/Shape
.3x.7/Elliptical
Load Impedance
47k Ohms
Tracking Force Range
1.8-2.2 grams
Recommended Force
2.0 grams
Cartridge Weight
6.5 grams
Tone Arm
9” vertical Yoke type tonearm with lateral
type bearing
Damped machined aluminum tube arm
Pivot to spindle
223mm
Eective length
240.7mm
Tone Arm (cont’d)
Overhang
17.7mm
Oset angle
22.85 degrees
Average RMS distortion
.36%
The Table
3/8-inch Thick Glass anchored to custom
1/4-inch thick aluminum metal plate for
stability
Aluminum Platter
Platter rotates on an oil bath bearing
The bearing has a high performance
polyetheretherketone (PEEK) thrust disc
and machined graphite impregnated brass
bushings using a Thompson Engineering 60
Rockwell case hardened shaft
Motor
600 RPM Direct Drive Permanent Magnet
AC Synchronous Motor AC - 2 speed pulley
Tur ntable Speeds
33.3 RPM and 45 RPM
General
Power Requirements
Refer to the rear panel of the MTI100
for the correct voltage. The MTI100 is fac-
tory congured for one of thefollowing
AC Voltages:
100 Volts, 50/60Hz at 50 watts
110 Volts, 50/60Hz at 50 watts
120 Volts, 50/60Hz at 50 watts
220 Volts, 50/60Hz at 50 watts
230 Volts, 50/60Hz at 50 watts
240 Volts, 50/60Hz at 50 watts
Standby Power, less than 0.5 watts
Field AC Voltage conversion of the MTI100
is not possible.
Dimensions
Width 19-1/4 inches (48.9cm)
Height 6-3/4inches (17.15cm) including feet
Depth 14 inches (35.6cm) including antenna
Weight
33.5 pounds (15.2 kg) net
40.5 pounds (18.4 kg) in shipping carton
Shipping Carton Dimensions
Width 24 inches (68.6cm)
Height is 16-1/2 inches (35.6cm)
Depth is 17-1/2 inches (63.5cm)