What to do if my McQuay M4MC Air Conditioner is not cooling enough?
If your McQuay Air Conditioner isn't cooling sufficiently, it might be due to a dirty indoor or outdoor coil. Try cleaning the coil. Also check for any obstructions at the air inlet or outlet of the indoor or outdoor unit and remove them. It could also be caused by a refrigerant short charge or leakage, in which case you should add refrigerant and repair the leakage.
How to fix a McQuay M4MC Air Conditioner that won't turn on (no cooling/heating)?
If your McQuay Air Conditioner fails to start, it could be due to a faulty contactor, contacts or motor. Try changing the contactor or the contacts. You might also need to repair or change the motor.
Why McQuay M4MC Air Conditioner shows high side low side?
If your McQuay Air Conditioner is showing a high side low side issue, it could be due to: * An undercharge of refrigerant. * Refrigerant leakage. * A clogged or dirty air filter in the indoor unit. * A locked indoor fan (during cooling). * A defective defrost control causing outdoor coil freeze-up (during heating). * A locked outdoor fan (during heating).
General| Brand | McQuay |
|---|---|
| Model | M4MC |
| Category | Air Conditioner |
| Language | English |
Lists McQuay brand names for various fan coil units and condensing units.
Provides conversion values for capacity, pressure, flow rate, temperature, velocity, volume, and area.
Maps main boards to compatible handset models for various HVAC unit types.
Details the functions and operation of the G6 remote control for HVAC units.
Explains the features and usage of the G7 remote control for HVAC systems.
Describes the functions and operation of the G11 remote control, including special features.
Outlines the operation and features of the G17 remote control for HVAC units.
Details the operation and features of the GS01 remote control for HVAC systems.
Explains the functions and LCD display of the APJ1 remote control.
Describes the operation and features of the SLM3 wired controller.
Details the operation and settings of the SLM8 wired controller.
Explains the functions and operation of the sequential controller.
Differentiates Netware 3 and 3C, and outlines their operating guides.
Guides the operation of the rooftop panel display and controls.
Explains the operation of the chiller panel display and controls.
Details the operation, settings, and clock functions of the MC301 remote.
Explains the operation, address register, and clock settings of the MC303 remote.
Explains how to configure the auto random restart function using jumpers.
Describes the three available selections for hot keep function based on jumpers.
Details dip switch settings for models, operating modes, and hot keep options.
Explains jumper selections for valve and heat configuration in W1V3 units.
Details jumper configurations for operating modes in W2.0 units.
Summarizes hardware settings for SLM8, controlling temperature range and turbo/quiet features.
Details components needed to convert U1.5 heatpump PCB for auxiliary heater application.
Explains how to convert cooling-only and heatpump models to multi-split units.
Outlines the necessary steps and spare parts for converting U1.5 PCB to L208A PCB.
Details the conversion process from U1.4 to L2EF PCB, noting display panel incompatibility.
Describes the work indication for converting SQ Board for wiring up to 1000m.
Explains how to use the temperature sensor on the Netware 3 controller as a room sensor.
Correlates LED patterns to operational/faulty indications and actions for specific models.
Lists error codes and faulty indications for various handset models and unit types.
Details MDS diagnosis via indoor unit LEDs and wired controller error codes.
Provides a troubleshooting guide for common unit malfunctions and suggested actions.
Offers troubleshooting based on pressure readings and probable causes for HVAC units.
Provides thermistor resistance values across a range of temperatures for HVAC units.
Outlines compatibility between MDS indoor PCBs, wired handsets, and outdoor PCBs.
Details dip switch settings for MDS outdoor units based on PCB version and HP.
Specifies cable lengths for various wired handset types and their standards.
To Next Page
