EasyManua.ls Logo

MEDAP MEDAP-BORA UP 2080 - User Manual

Default Icon
60 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
OPERATING INSTRUCTIONS
UNIVERSAL ASPIRATOR
MEDAP-BORA UP 2080
MEDAP-BORA UP 2080 OP
GA 5752 2300 GB 26

Table of Contents

Questions and Answers

  • R
    Robin BrewerAug 14, 2025
    What to do if MEDAP MEDAP-BORA UP 2080 Medical Equipment has reduced or no flow rate?
    • J
      Jeremiah JohnsonAug 14, 2025
      If your MEDAP Medical Equipment aspirator shows a reduced or no flow rate, make sure the septic fluid jar cap is correctly positioned. Also, check if the hydrophobic filter is clogged (if the vacuum gauge indicates vacuum, replace the filter). Inspect the tube for cracks and replace it if necessary. Replace any contaminated or porous seals. Ensure the septic fluid jar cap closes properly, replacing it if the clamp is bent. If the septic fluid jar is full, empty it and clean or replace the jar and mechanical overflow protection. Clean the overflow protection device or replace the septic fluid jar cap if it's contaminated with exudate. Finally, check and clean the tube connection in the septic fluid jar cap if it's clogged.
  • K
    Katherine DeleonAug 17, 2025
    How to fix MEDAP MEDAP-BORA UP 2080 aspirator that doesn't start but the operating status display is illuminated?
    • D
      Dennis TaylorAug 17, 2025
      If your MEDAP Medical Equipment aspirator does not start but the operating status display is illuminated, the vacuum may still be present. To resolve this, switch off the aspirator, turn the regulating knob to the left, and then switch the aspirator back on. If the issue persists, the motor may be defective, and you should have the equipment repaired by a service technician authorized by ATMOS.
  • A
    Ann WilliamsAug 20, 2025
    What to do if MEDAP Medical Equipment aspirator does not start and the operating status display is not illuminated?
    • A
      Angela EdwardsAug 21, 2025
      If your MEDAP Medical Equipment aspirator does not start and the operating status display is not illuminated, check that the equipment and mains plugs are properly seated in the socket. Also, verify that there is proper voltage and check the building fuse, and the specifications on the type plate. If the mains fuse is defective, replace it.
  • H
    howardphillipsAug 25, 2025
    What happens if MEDAP MEDAP-BORA UP 2080 Medical Equipment aspirator has been exposed to oversuction?
    • B
      Brandon RogersAug 25, 2025
      If the MEDAP Medical Equipment aspirator has been exposed to oversuction because no mechanical overflow protection device and no hydrophobic bacterial filter were installed, the aspirator may no longer be used. Have the equipment repaired by a service technician authorised by ATMOS.
  • J
    Jonathan WilsonAug 27, 2025
    Why MEDAP MEDAP-BORA UP 2080 with foot switch doesn't start, yellow LED is on?
    • J
      Julia GonzalezAug 27, 2025
      If the MEDAP Medical Equipment aspirator with foot switch does not start and the yellow LED is illuminated, the aspirator is likely in standby mode. To resolve this, switch off standby mode using the foot switch. The aspirator will then start operating. Operating the foot switch again will switch the aspirator back into standby mode.
  • J
    Joseph GreenAug 30, 2025
    How to resolve MEDAP MEDAP-BORA UP 2080 Medical Equipment that cannot be switched on and off?
    • S
      stephaniewoodwardAug 30, 2025
      If your MEDAP Medical Equipment cannot be switched on or off, the electronics are likely defective. In this case, have the equipment repaired by a service technician authorized by ATMOS.
  • F
    ffarmerSep 3, 2025
    What to do if MEDAP Medical Equipment aspirator operates but operating status display is not illuminated?
    • D
      duanefrazierSep 3, 2025
      If the MEDAP Medical Equipment aspirator is operating, but the operating status display is not illuminated, the LED on the operating status display is likely defective. You should have the equipment repaired by a service technician authorized by ATMOS.
  • C
    Cathy NovakSep 6, 2025
    Why vacuum cannot be regulated on MEDAP Medical Equipment?
    • C
      calebperkinsSep 6, 2025
      If the vacuum of your MEDAP Medical Equipment cannot be regulated, the membrane regulator is likely defective. You should have the equipment repaired by a service technician authorized by ATMOS.
  • C
    cynthiatateSep 10, 2025
    What to do if MEDAP MEDAP-BORA UP 2080 aspirator is working but vacuum gauge indicates no vacuum?
    • R
      Rodney MaciasSep 10, 2025
      If your MEDAP Medical Equipment aspirator is working but the vacuum gauge indicates no vacuum, the vacuum gauge is likely defective. Have the equipment repaired by a service technician authorized by ATMOS.

MEDAP MEDAP-BORA UP 2080 Specifications

General IconGeneral
CategoryMedical Equipment
ModelMEDAP-BORA UP 2080
TypeUltrasound therapy device
DisplayLCD
Frequency1 MHz
Pulse Ratio1:1, 1:2, 1:4, 1:8
Timer1 - 30 min
Power Supply50Hz

Related product manuals