Medline ReadyBath MSCWARMER 28S - User Manual

Hit
ONCE
Use arrows to
increase or decrease
temperature
RECOMMONDED
FACTORY
DEFAULT
125°F
TO ENTER SET-POINT TEMPERATURE

See
Unit
PAGE 1
Power Source: AC 115 (+/-10%), 60HZ, Max Watts: 300 (14S and 28S)
Maximum Temperature: 54
o
C / 130
o
F
Operating Environment: Indoor use, altitude up to 6,500 ft (2,000m).
Installation Category II, Pollution Degree 2,
ambient Conditions 10
o
C / 50
o
F to 35
o
C /95
o
F, 80% RH maximum.
Storage Temperature: -10
o
C / 14
o
F to 70
o
C / 158
o
F, 70% RH maximum
Approvals: Underwriter's UL / CUL, United States / Canadian for laboratory equipment.
Compliance: UL Standard 61010-1, IEC 61010-1 .
Exterior: Powder Coated Steel Interior: Aluminum
Insulation: Fiberglass Door: Acrylic
Thermo-control: PID Microprocessor Heater: Resistive-Tubular Incoloy
Unit Construction
MHSe WARMER14S MHSe WARMER28S
Capacity: 14 ReadyBaths Capacity: 28 ReadyBaths
Exterior Dimensions: 12.87"(32.6 cm)W x Exterior Dimensions: 22.14" (56.2cm)W x
18.00" (45.7 cm)H x 13.43" (34.1 cm)D 18.00" (45.7 cm)H x 13.25" (33.6cm)D
Shipping Weight: 29 pounds / 13.1 kg Shipping Weight: 34 pounds / 15.4 kg
Net Weight: 23.5 pounds / 10.6 kg Net Weight: 28.5 pounds / 12.9 kg
Unit Specifications
The control's self diagnostics are part of Intelligent Warmer's "watch-dog" system that continuously monitor the warmer's
operating system, temperature and performance. In the event of any of the operating alarm conditions, an alarm prompt
will continuously appear on the control display. The alarm conditions are described below. All alarm conditions will
automatically discontinue heater operation.
Medline Industries, Inc. Three Lakes Drive Northfield IL 60093 1-800-MEDLINE
Control prompts will only display when a fault or alarm condition exists.
Control Self Diagnostics
Indicates Connection Error
ALARM Codes "Err1" & "Err6"
or
Check the wiring connections
Indicates Open Input / No Sensor Error
ALARM Code "- - - -"
Check connection between Controller
and Thermocouple
Indicates Internal Memory Error
ALARM Code "E111"
Turn Controller OFF and On. If problem
remains, replace Controller
Indicates Watchdog Error
ALARM Code "Err4"
Controller needs to be replaced
Indicates Thermocouple Sensor Error
ALARM Code "Err8"
Turn off and wait until ambient
temperature recovers
Indicates Sensor Temp Over/Under Error
ALARM Code "nnnn" & "vvvv"
Increase or reduce process temperature
to get back in range
or
Operating Specifications
Issue Rev C 10 19
Controller Functions Buttons
MENU
Functions
Decrease
Increase








The warmers’ controller allows you to set and change the
units operating temperature between 100°F and 130°F,
and change the read out units to either °C or °F. These are
the only settings that can be changed. There are other
controller settings that are visible, but for safety and opera-
tional purposes can not be changed.
Hit
TWICE
Use arrows to
change temperature
units readout
FACTORY
DEFAULT
°F
TO CHANGE TEMPERATURE READ OUT

See
Unit
For questions regarding:
Technical Support
General Product Information, please contact:
Technical Support/Parts Order, please contact: PH: 1-800-482-HEAT FAX 773-622-2282
Copyright Quincy Lab Inc. 2018
Warmer Maintenance
Periodic cleaning is the only required maintenance for the Warmer. Disconnect the power cord before cleaning. To
clean interior and exterior surfaces, use a soft damp cloth. Avoid excessive amounts of water that could drip into the lower
plenum. Use a mild detergent or cleaner if necessary.
The door should only be cleaned using a lint-free cloth. Paper towels can mar the surface of the door. Do Not use any
commercial or alcohol-based cleansers on the door. This will cause cracking of the acrylic over time.
Medline Industries, Inc. Three Lakes Drive,
Northfield, IL 60093
1-800-MEDLINE (633-5463)
medline.com | info@medline.com
PAGE 4
To return to temperature display, aer making any change, simply press the buon unl you see the warmer’s temperature
on the display. If you are in an area of the MENU not shown press and hold unl you see the warmer’s current temperature.
P
P
Models MSCWARMER 14S & 28S
Operating Manual
NEXTGEN Warmer
INTELLIGENT WARMER
125
P
F
WARMING - Solid Red LED - Pack has not yet reached required temperature
HEATED - Solid Green LED - Packs have reached the required temperature and are ready to use.
TAKE FIRST - Green LED Flashes - Pack has been in the warmer for 84 hours. These packs should be used first.
DISCARD - Red LED Flashes - Pack has been in the warmer longer than 250 hours and should be discared.
INTELLIGENT WARMER
125
P
F
WARMING - Solid Red LED - Pack has not yet reached required temperature
HEATED - Solid Green LED - Packs have reached the required temperature and are ready to use.
TAKE FIRST - Green LED Flashes - Pack has been in the warmer for 84 hours. These packs should be used first.
DISCARD - Red LED Flashes - Pack has been in the warmer longer than 250 hours and should be discared.
Model 28S Model 14S

Summary

Controller Functions and Operation

Setting Temperature

Instructions on entering set-point temperature and changing readout units (°F/°C).

Control Panel Overview

Description of controller buttons: Menu, Increase, Decrease, Functions.

Control Self Diagnostics and Alarms

Alarm Code Troubleshooting

Explanation of various alarm codes (Err1, Err6, ----, E111, Err4, Err8, nnnn, vvvv) and their causes.

Warmer Maintenance and Support

Cleaning Procedures

Guidance on cleaning interior/exterior surfaces and the door using soft cloth and mild detergent.

Technical Support Contact

Contact information for general product questions and technical support/parts orders.

Safety Precautions

General Safety Warnings

Important warnings regarding electrical shock, fire risk, proper product use, and environmental hazards.

Set-Up & Installation

Installation Guidelines

Recommendations for warmer placement, ventilation, power connection, and avoiding environmental interference.

General Operation

Startup and Heating

Instructions on powering the unit, initial LED status, heating process, and temperature holding.

ReadyBath Safety Alarms Reset

Electronic Fail Alarm Reset

Procedure to reset the unit after an electronic fail safety alarm, involving cooling and power cycling.

Thermo Safety Alarm Reset

Procedure to reset the thermo safety shut-off via a 'snap disc' on the bottom cover.

ReadyBath Product Loading and Retrieval

Product Loading

Guidelines for inserting ReadyBath products into slots, ensuring correct placement for sensor detection.

Indicator Sensor Status

Explanation of LED indicator lights (Solid Red, Solid Green, Flashing Green, Flashing Red) and their meaning.

Product Loading Tips

Advice on stocking levels and proper placement of labels to prevent staining of shelves.

Medline ReadyBath MSCWARMER 28S Specifications

General

Brand	Medline
Model	ReadyBath MSCWARMER 28S
Category	Food Warmer
Language	English