What to do if MEI Vending machine shows no LED on?
First, visually inspect the power supply to the vending machine for any power-on light or other indications. Then, ensure the cable connection between the changegiver and the vending machine is secure.
What to do if my MEI Vending machine shows an Amber LED Steady?
An amber LED indicates several potential issues. First, check the loom connecting the changegiver to the vending machine to ensure it is secure. Second, if applicable, replenish the vending machine. The issue might also be a jammed or faulty merchandise dispenser or a vending machine controller problem.
What causes Coin Sensor Error in MEI CashFlow 690 Executive/MDB/BDV Vending machines and how to fix it?
A coin sensor error is caused by an electronics error. To solve this, switch the power off and then on again. If the fault persists, replace the changegiver and return the faulty one to an Approved Service Centre for servicing.
How to fix coin jam in MEI CashFlow 690 Executive/MDB/BDV?
First, check for a coin jam. Also, ensure that the reject lever mechanism is functioning freely and that there is enough clearance between the changegiver.
What does AGM error mean on my MEI Vending machine and how can I resolve it?
An AGM error often indicates a coin jam or debris in the accept gate area. Open the acceptor and clear any obstructions. Also, ensure the acceptor gate mechanism is clean and that no coins are holding the gate. Finally, close the acceptor completely.
What does 'Escrow pressed' mean on MEI Vending machine and what to do?
If the 'Escrow pressed' error appears, start by checking the flight deck. Then, verify that the changegiver escrow lever and the vending machine's escrow mechanics are functioning freely. Also, check for adequate clearance between the escrow lever on the changegiver and the lever on the vending machine, as the cause may be an escrow jammed open or a stuck reject lever.
What does 'Clean-Me' mean on MEI CashFlow 690 Executive/MDB/BDV Vending machines and how to fix it?
The 'Clean-Me' message indicates dirty coin paths. To resolve this, clean the coin paths. On the keypad, press Mode A Mode to stop the LED flashing.
What does 'Dispenser error.x' mean on MEI Vending machines and how to resolve it?
A 'Dispenser error.x' indicates a coin jam at the bottom of the indicated coin tube or a loom that is not fitted correctly. To resolve this, first free the jam and check that the loom is correctly fitted. Additionally, press the Mode key twice to park the dispenser arms and consider replacing the cassette.
What does 'Separator error.x' mean on MEI CashFlow 690 Executive/MDB/BDV and how to fix it?
A 'Separator error.x' typically means there is a coin jam at the top of a coin tube, the cassette is dirty or not properly in place, there is dirt on the top-level sensor, or the cassette is not assembled correctly. If possible, remove the coin tube cassette, clear the jam, clean the sensor, and then replace the cassette.
General| Type | Bill Validator |
|---|---|
| Model | CashFlow 690 Executive/MDB/BDV |
| Interface | MDB or BDV |
| Currencies | Configurable for various global currencies |
| Security Features | Optical |
| Connectivity | MDB or BDV interface |
| Operating Temperature | 0°C |
| Protocol | MDB (Multi-Drop Bus), BDV (Binary Data Validation) |
| Compatibility | Vending machines compliant with MDB or BDV standards |
Warns against operation in flammable gasses, fumes, or water.
Details how to enter the Service mode using the Mode key.
Guides on filling, resetting, and emptying coin tubes to manage float levels.
Explains how to enable/inhibit coins, view channel details, and select Euro stages.
Details setting prices and managing coin cassettes.
Key steps before replacement: turn off power and check voltage compatibility.
Guides on installing the new unit and connecting cables, including checks.
To Next Page
