What to do if MEI Vending machine shows no LED on?
First, visually inspect the power supply to the vending machine for any power-on light or other indications. Then, ensure the cable connection between the changegiver and the vending machine is secure.
What to do if my MEI Vending machine shows an Amber LED Steady?
An amber LED indicates several potential issues. First, check the loom connecting the changegiver to the vending machine to ensure it is secure. Second, if applicable, replenish the vending machine. The issue might also be a jammed or faulty merchandise dispenser or a vending machine controller problem.
What causes Coin Sensor Error in MEI Cashflow 690 and how to fix it?
A coin sensor error is caused by an electronics error. To solve this, switch the power off and then on again. If the fault persists, replace the changegiver and return the faulty one to an Approved Service Centre for servicing.
How to fix coin jam in MEI Cashflow 690 Vending machines?
First, check for a coin jam. Also, ensure that the reject lever mechanism is functioning freely and that there is enough clearance between the changegiver.
What does AGM error mean on my MEI Vending machine and how can I resolve it?
An AGM error often indicates a coin jam or debris in the accept gate area. Open the acceptor and clear any obstructions. Also, ensure the acceptor gate mechanism is clean and that no coins are holding the gate. Finally, close the acceptor completely.
What does 'Escrow pressed' mean on MEI Vending machine and what to do?
If the 'Escrow pressed' error appears, start by checking the flight deck. Then, verify that the changegiver escrow lever and the vending machine's escrow mechanics are functioning freely. Also, check for adequate clearance between the escrow lever on the changegiver and the lever on the vending machine, as the cause may be an escrow jammed open or a stuck reject lever.
What does 'Clean-Me' mean on MEI Cashflow 690 and how to fix it?
The 'Clean-Me' message indicates dirty coin paths. To resolve this, clean the coin paths. On the keypad, press Mode A Mode to stop the LED flashing.
What does 'Dispenser error.x' mean on MEI Cashflow 690 Vending machines and how to resolve it?
A 'Dispenser error.x' indicates a coin jam at the bottom of the indicated coin tube or a loom that is not fitted correctly. To resolve this, first free the jam and check that the loom is correctly fitted. Additionally, press the Mode key twice to park the dispenser arms and consider replacing the cassette.
What does 'Separator error.x' mean on MEI Cashflow 690 Vending machines and how to fix it?
A 'Separator error.x' typically means there is a coin jam at the top of a coin tube, the cassette is dirty or not properly in place, there is dirt on the top-level sensor, or the cassette is not assembled correctly. If possible, remove the coin tube cassette, clear the jam, clean the sensor, and then replace the cassette.
Explains compliance with safety standards like IEC335/EN60335.
States the operating voltage and cautions against using other sources.
Warns against operating in flammable or wet conditions.
Advises against disposal by incineration.
Introduces the changegiver and its components.
Outlines procedures for carrying out servicing.
Describes routine cleaning requirements.
Explains how to identify and resolve problems.
Details the process of replacing a faulty unit.
Describes the modular structure and principal components.
Explains the electronic setup and configuration options.
Details the user interface elements, including LEDs and keys.
Describes the function of the coin tube cassette.
Describes the function of the acceptor/separator unit.
Describes the function of the coin dispenser.
Explains how to enter the Service mode using the Mode key.
Details procedures for managing coin float levels (Up, Reset, Down).
Explains enabling/inhibiting coins and viewing channel status.
Describes setting or amending merchandise prices.
Covers selecting and customizing coin cassettes.
Describes how to display a quick audit of coin totals.
Provides a general overview of troubleshooting indicators and LED status.
Describes faults indicated by the amber LED.
Details issues indicated by a steady amber LED.
Explains faults indicated by one amber flash.
Explains faults indicated by two amber flashes.
Explains faults indicated by three amber flashes.
Explains faults indicated by four amber flashes.
Addresses issues when no LED indicator is lit.
Describes how to access and interpret error messages.
Covers initial steps before replacing the changegiver.
Details the mounting and fixing points for the changegiver.
Provides instructions for removing the changegiver.
Covers the process of installing the new changegiver.
Lists checks to perform after installation.
Details how to connect power and data cables.
General| Manufacturer | MEI |
|---|---|
| Model | Cashflow 690 series |
| Category | Vending machines |
| Bill Validator | Yes |
| Currency Recognition | Multi-currency |
| Type | Bill Validator |
| Coin Mechanism | Yes |
| Connectivity | MDB |
| Security Features | optical sensors |
| Dimensions | Varies by model |
| Weight | Varies by model |
| Interface | MDB |
| Protocol | MDB |
| Currency Types Supported | Configurable for various currencies |
To Next Page
