Memphis Shades MEM-9888

To Next Page

MEM-9888

LOW PROFILE INDEPENDENT LOWERS HARDWARE KIT FOR EXPOSED

FORKS 35-43MM

TOOLS REQUIRED: 3/16” Allen wrench (provided)

1. Cover the front fender with a towel, in case you drop something.

Note:

The neoprene washer has been replaced by four Santoprene grommets. The rubber

grommets should be inserted through the holes in the windshield so that the flat round part

of the grommet lays flat on each side of the windshield.

2. Attach the lowers plastic to the lowers mounting plates using the pre-assembled bolts and button nuts. Install the

components in the order shown in Figure 1.

3. The mounting plate tabs should point away from each other when installed correctly. (see Figure 2)

Note

: The mounting plates can be mounted pointing up, for those applications where the

windshield is too short to reach them other wise

4. Loosely install the two fork clamps onto the forks. MAKE SURE THE LOWERS WILL CLEAR ALL

FENDERS, RADIATORS, OIL COOLERS, ETC. WHEN INSTALLED. Attach the lowers mounting plates

to the fork clamps. Adjust height, angle and position of the clamps and then tighten them.

Fig. 1 Order of assembly Fig.2 Position of plate tabs

CARE AND CLEANING

To clean your windshield, wash it with warm water and a mild, non-abrasive, dishwashing liquid. Use a soft

cloth such as a T-shirt or flannel cloth.

To protect your windshield, use NOVUS #2 to remove minor scratches, or use

Memphis Shades Shinola polish specially designed for plastic. NEVER use glass

cleansing agents, they may cause severe damage to your windshield.

Never use any petroleum-based chemicals, or cleaning agents with ammonia.

All manuals and user guides at all-guides.com

Need help?

Do you have a question about the Memphis Shades MEM-9888 and is the answer not in the manual?

Summary

Installation Instructions

Tools Required

Lists the necessary tools for the installation process, including a provided Allen wrench.

Step 1: Prepare Fender

Cover the front fender with a towel to prevent dropping parts.

Step 2: Attach Lowers to Plates

Attach the lowers plastic to mounting plates using bolts and nuts as shown in Figure 1.

Step 3: Mount Plate Tab Orientation

Ensure mounting plate tabs point away from each other; adjust plate position if needed.

Step 4: Install Fork Clamps

Loosely attach fork clamps, verify clearance, then attach mounting plates and tighten.

Parts List and Contact Information

Parts Identification

Details the specific part numbers, descriptions, and quantities for the mounting kit components.

Warranty and Support Contact

Provides contact details for parts, warranty help, and company website.

This document describes the MEM-9888 Low Profile Independent Lowers Hardware Kit for Exposed Forks 35-43mm, a product designed to attach lowers to motorcycles. The kit includes various components and provides instructions for installation, usage, and maintenance.

Function Description:

The MEM-9888 kit is designed to provide a mounting solution for independent lowers on motorcycles with exposed forks ranging from 35mm to 43mm in diameter. Lowers are typically used to enhance rider comfort by deflecting wind and debris, especially from the lower body. This hardware kit facilitates the secure attachment of these lowers to the motorcycle's fork tubes. The "low profile" aspect suggests a design that aims to be less obtrusive or bulky, integrating more seamlessly with the motorcycle's aesthetics while still providing functional benefits. The "independent" nature of the lowers implies that they are mounted separately from other fairing components, offering flexibility in installation and potentially allowing for a more customized look or specific aerodynamic benefits. The kit is supplied with a 3/16" Allen wrench, indicating that this is the primary tool required for assembly and adjustment.

Important Technical Specifications:

Compatibility: Designed for exposed forks with diameters between 35mm and 43mm. This specific range ensures proper fitment and stability for a variety of motorcycle models within this fork size category.
Hardware Components: The kit includes a comprehensive set of parts necessary for installation. These include:
- M888: Instruction Sheet / Parts List (Qty: 1)
- S1085: Lowers Mounting Bracket Left Sub-Assembly (Qty: 1)
- S1086: Lowers Mounting Bracket Right Sub-Assembly (Qty: 1)
- S1074: Small Adj. Fork Clamp Sub-Assembly (Qty: 2)
- M313: 3/16" Allen Wrench Holder (CAP) (Qty: 1)
- M310: 3/16" Short Arm Allen Wrench (Qty: 1)
Mounting Mechanism: The system utilizes fork clamps that attach to the motorcycle's forks. The lowers plastic then attaches to mounting plates, which in turn connect to the fork clamps. The design incorporates pre-assembled bolts and button nuts for securing the lowers plastic to the mounting plates.
Grommet System: An important design note indicates that the traditional neoprene washer has been replaced by four Santoprene grommets. These grommets are designed to be inserted through the holes in the windshield, with the flat round part of the grommet laying flat on each side of the windshield. This suggests a cushioning or vibration-damping function, likely to protect the windshield and ensure a secure, rattle-free fit.
Adjustability: The instructions mention adjusting the height, angle, and position of the clamps before tightening, indicating that the system allows for customization of the lowers' placement to suit rider preference or specific aerodynamic needs. The mounting plates can also be oriented pointing up for applications where the windshield might be too short otherwise, offering further installation flexibility.

Usage Features:

Installation Process: The installation involves several key steps:
1. Preparation: Covering the front fender with a towel to prevent damage during installation.
2. Assembly of Lowers: Attaching the lowers plastic to the mounting plates using pre-assembled bolts and button nuts. The correct orientation of the mounting plate tabs (pointing away from each other) is crucial.
3. Fork Clamp Installation: Loosely installing two fork clamps onto the forks.
4. Clearance Check: Crucially, ensuring that the lowers will clear all fenders, radiators, oil coolers, etc., once installed. This step is vital for preventing damage and ensuring safe operation.
5. Final Attachment and Adjustment: Attaching the lowers mounting plates to the fork clamps, followed by adjusting the height, angle, and position of the clamps before final tightening.
Flexibility in Mounting: The ability to mount the plates pointing up provides adaptability for different windshield heights, ensuring the kit can be used across a broader range of motorcycle setups.
Provided Tool: The inclusion of a 3/16" Allen wrench simplifies the installation process, as users do not need to source this specific tool separately.

Maintenance Features:

Windshield Cleaning: The manual provides specific instructions for cleaning the windshield, which is likely part of the lowers assembly.
- Recommended Method: Wash with warm water and a mild, non-abrasive dishwashing liquid.
- Recommended Cloth: Use a soft cloth such as a T-shirt or flannel cloth.
- Prohibited Cleaners:
  - NEVER use glass cleansing agents, as they can cause severe damage to the windshield.
  - NEVER use any petroleum-based chemicals or cleaning agents with ammonia.
Scratch Removal and Polish:
- Minor Scratches: Use NOVUS #2 for removal.
- General Polish: Use Memphis Shades Shinola polish, which is specifically designed for plastic.
Warranty: Memphis Shades offers a 24-month warranty on all product components (metal and plastic) against defects in materials and workmanship. This provides assurance regarding the quality and durability of the product.
Support: Contact information for parts and warranty help is provided, including a mailing address, phone number, website (www.memphisshades.com), and customer service email (customerservice@memphisshades.com). This ensures users have access to assistance if needed.