Mercury Security MR16out - User Manual

Mercury Security Corporation © 2009 MR16out DOC 10107-0012 REV 2.01 Page 1
www.mercury-security.com
2355 MIRA MAR AVE. LONG BEACH, CA 90815-1755, (562)986-9105 FAX (562) 986-9205
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
12 TO 24Vdc
GND
VIN
+
-
TB11
MR16out PROCESSOR
Installation and Specifications:
1. General:
The MR16out processor provides a solution to the OEM system integrator for output control. The
controller has 16 form-C contact relays for load switching. Additionally, 2 digital inputs are provided for
tamper and power fault status monitoring. The processor requires 12 to 24Vdc for power.
2. Supplying Power to the MR16out:
The MR16out requires 12 to 24Vdc for power on TB11. Locate power
source as close to the unit as possible. Connect power with minimum of
18AWG wires.
Observe POLARITY on VIN!
6.00 [152.40]
5.50 [139.70].25 [6.35]
2.00 [50.80]3.00 [76.20]2.00 [50.80]
8.00 [203.20]
S1
1
1 2 43 5 12976 8 13 1410 11 15 16
TB10
TR+
GND
R+
4W
R-
2W
TR-
RS-485
GND
VIN
GND
BA
CT
GND
TB9
TB11
J2
J1
J1, J2
RS-485
TERM
NC
C
NO
NC
C
NO
OUT 8
OUT 7
TB4 K8
NO
C
NC
NO
C
NC
OUT 6
OUT 5
NO
C
NC
NO
C
NC
OUT 4
OUT 3
NO
C
NC
NO
C
NC
OUT 2
OUT 1
TB3K7 TB2 TB1
2W
4W
J3
U1
J6
J5
J7
J8
J4
A
B
CT
BA
2
3
4
5
6
7
8
K2
K4
K3
K1
K9
K11
K12
K10
K5
K13
K14
K15
K16
TB5
TB6
TB7
TB8
NO
C
NC
NO
C
NC
OUT 9
OUT 10
C
NO
NC
C
NO
NC
OUT 11
OUT 12
NC
C
OUT 13
NO
NC
OUT 14
NO
C
OUT 16
NO
C
OUT 115
NC
C
NO
NC
K6
POWER IN
12-24Vdc
SIO COMMUNICATION
PORT, RS-485
TAMPER AND POWER
MONIOTR INPUTS
DIP SWITCHES
STATUS LEDs
Ø.156 [Ø4.0]
8 PLACES
OUTPUTS
OUTPUTS
RELAY STATUS LEDs
.50 [12.70]

Mercury Security MR16out Specifications

Power

primary power voltage range	12 to 24 Vdc ±10%
primary power maximum current	1100 mA
nominal current at 12 Vdc	850 mA
nominal current at 24 Vdc	450 mA

Relay Contacts

relay contact type	16 Form-C
relay contact rating	5 A @ 30 Vdc
relay contact resistance	resistive

Operating Environment

storage temperature range	-55°C to +85°C
operating temperature range	0°C to +70°C
humidity range	0% to 95% RHNC

Weight and Dimensions

dimension width	6 in (152 mm)
dimension length	8 in (203 mm)
dimension height	1 in (25.4 mm)
weight	14 oz (400 gm) nominal

Summary

General Information

MR16 out Processor Overview

Provides OEM system integrator solution with 16 form-C relays and 2 digital inputs for tamper and power fault monitoring.

Power Requirements

The MR16out processor requires 12 to 24Vdc for power.

Communication Wiring

RS-485 Interface Configuration

Details RS-485 interface for multi-drop communication, cable requirements, and jumper settings.

Cabinet Tamper and Power Fault Inputs

Cabinet Tamper and Power Fault Inputs

Describes monitoring cabinet tamper and power failure using normally closed contacts via CT and BA inputs.

Relay Outputs Usage

Relay Outputs Usage

Shows typical use of relays with DC power, recommending transient clamping for protection and EMI reduction.

DIP Switch and Jumper Usage

DIP Switch Settings for Address and Baud Rate

Switches 1-5 select device address, 6-7 select baud rate, and 8 enables encrypted communication.

DIP Switch Notes

Clarifies settings for 2,400 BPS for older firmware (Note 1) and SW8 definition (Note 2).

Jumpers Configuration

Jumper Descriptions

Details function of jumpers J1-J9, including RS-485 termination and 2-wire/4-wire selection.

Status LEDs

LED Status Meanings

Explains meanings of LEDs A, B, CT, BA, and 1-16 for heartbeat, communication, tamper, fault, and output status.

Technical Specifications

Power, Relay, and Input Specifications

Details primary power, relay contacts, input types, and communication protocols supported.

Cable, Mechanical, and Environmental Specifications

Covers cable requirements, physical dimensions, weight, operating temperature, and humidity.

Warranty and Liability Information

Outlines product warranty terms and limits liability for misapplication or malfunction.