Why is my Metso Outotec Lokotrack ST3.8 system display not starting?
The system display might not start due to several reasons: the battery could be empty, the main switch might be in the OFF position, or the battery clamps may not be properly attached. Ensure the main switch is ON, charge the Lokotrack unit's battery, jump start the engine, or ensure the battery clamps are securely attached.
What to do if my Metso Outotec Lokotrack ST3.8 Industrial Equipment engine start failed?
If the engine fails to start, make sure that the main switch is in the ON position. Also, check that none of the emergency stop buttons or the remote stop button are pressed down.
What to do if my Metso Outotec Industrial Equipment engine start failed because of the hydraulic oil level?
If the engine start failed, it might be due to a low hydraulic oil level. Check the hydraulic oil level and inspect for any potential leaks.
What to do if my Metso Outotec Industrial Equipment engine start failed because of the hydraulic shut-off valve?
If the engine start failed, verify that the hydraulic shut-off valve is open.
What to do if my Metso Outotec Lokotrack ST3.8 engine start failed because of the hydraulic oil temperature?
If the engine start failed, it might be caused by the hydraulic oil temperature being too high. Allow the system to recover from the high hydraulic oil temperature.
What to do if track drive does not work on Metso Outotec Lokotrack ST3.8 Industrial Equipment because of manual valve mode?
If the track drive isn't working, check if the manual valve mode is activated. Ensure the manual valves are not engaged.
What to do if track drive does not work on Metso Outotec Lokotrack ST3.8 Industrial Equipment because the process is not stopped?
If the track drive is not working, verify that the process is stopped.
What to do if track drive does not work on Metso Outotec Lokotrack ST3.8 Industrial Equipment because manual controls are active?
If the track drive is not working, check if the manual controls are active.
Details general, personal injury, and crushing hazards during operation.
Illustrates forward, backward, left, and right movement directions.
Identifies the specific locations of emergency stop buttons on the machine.
Pinpoints the location of remote stop buttons on the control devices.
Details the functions of the physical drive control device levers and buttons.
Explains the operation of the wireless radio control device.
Outlines essential checks and conditions required before starting to drive.
Procedure to temporarily increase the machine's ground clearance for operation.
Covers safety precautions and the step-by-step procedure for starting the engine.
Step-by-step instructions for connecting the wired drive control device.
Steps for connecting and activating the wireless radio control device.
Instructions for operating the machine using the drive control device.
Instructions for operating the machine using the radio control device.
Procedure for safely shutting down and stopping the machine's engine.
A guide to identifying and resolving common operational problems and errors.
Ensures the main power switch is correctly positioned in the ON state.
Confirms emergency stop buttons are released and not pressed.
Ensures the remote stop button is released and not pressed.
Verifies that manual valves are in the OFF position for track driving.
Confirms that battery clamps are securely attached to the terminals.
Instructions for charging the machine's main battery.
Instructions for charging the battery of the radio control device.
Procedure for jump-starting the engine using an external vehicle.
Steps for starting the engine using a portable jump starter.
Guidance on checking and refilling the machine's fuel level.
General guidance on interpreting and responding to machine alarms.
Specific corrective actions for the 'Remote stop active' alarm.
Specific corrective actions for emergency stop alarms.
Steps to address excessive machine inclination for driving.
Procedure to check hydraulic oil level and inspect for leaks.
Instructions to open the hydraulic shut-off valve if it is closed.
Steps to manage and resolve high hydraulic oil temperature issues.
Verifies manual controls are inactive to enable track driving.
Stops the screening process to enable track driving.
General| Brand | Metso Outotec |
|---|---|
| Model | Lokotrack ST3.8 |
| Category | Industrial Equipment |
| Language | English |
To Next Page
