MHZ SOLIX EXTERNAL - English Adjustment Instructions: Resetting and Unpairing; Deleting End Positions and Unpairing Remotes; Factory Resetting and Channel Limiting

Subject to technical changes I Edition 04.2022
41
DE
FR
NL
EN
ES
IT
Adjustment instructions
Solix external roller blind
3.6 Deleting the end positions
1. With hand-held remote control units pull off the back cover to make the setting.
Caution: Keep battery gently pressed down (contact).
After making the setting, push the cover back on.
P2
P2
2. On the remote control unit press the P2 button once
=> Roller blind conrms with 1 beep + short movement.
3. On the remote control unit press the DOWN button once
=> Roller blind conrms with 1 beep + short movement.
4. On the remote control unit press the P2 button once
=> Roller blind conrms with  beeps + short movement.
3.7 Logging a remote control unit off
i
Only remote control b can be logged off.
1. With hand-held remote control units pull off the back cover to make the setting.
Caution: Keep battery gently pressed down (contact).
After making the setting, push the cover back on.
P2
P2
a
a
P2
b
P2
P2
a
b
+
a
b
2. On remote control unit a press the P2 button once
=> Roller blind conrms with 1 beep + short movement.
3. On remote control unit a press the P2 button once
=> Roller blind conrms with 1 beep + short movement.
4. On the remote control unit b press the P2 button once
=> Roller blind conrms with 5 beeps + short movement.
3.8 Resetting to factory settings using a paired hand-held
remote control
Delete all settings and all paired remote control units
1. With hand-held remote control units pull off the back cover to make the setting.
Caution: Keep battery gently pressed down (contact).
After making the setting, push the cover back on.
P2
P2
2. On the remote control unit press the P2 button once
=> Roller blind conrms with 1 beep + short movement.
3. On the remote control unit press the STOP button once
=> Roller blind conrms with 1 beep + short movement.
4. On the remote control unit press the P2 button once
=> Roller blind conrms with 5 beeps + short movement.
3.9 Resetting to factory settings without a hand-held remote
control
Delete all settings and all paired remote control units
1. Keep the setting button on the drive unit pressed.
=> Roller blind conrms with  short movements
4 seconds apart + 4 beeps after release of the
setting button.
=> for programming again, see step 3.1
3.10 Limit number of channels (applies only to 15-channel remote control units)
i
Using these settings, it is possible to limit the remote control unit to the number
of channels that are actually needed for controlling the drive systems. Using
channel ‘0’, all blinds are controlled.
1. On the remote control unit simultaneously press the
P1- and P1+ buttons.
=> the LCD display unit indicates ‘C’.
C
C
15
2
15
2
2
2
P1–
P1+
P1–
P1+
P1–
P1+
2. On the remote control unit keep the P1- and
P1+ buttons pressed.
=> the LCD display unit indicates ‘
15’.
3. On the remote control unit, press the P1- or P1+
button to select the number of channels. If, for
example, you are controlling only two drive units
with this remote control, select ‘
2’.
4. On the remote control unit press the STOP button
once.
=> the LCD display unit indicates ‘
’.
5. After a short time, limitation to two channels gets
indicated.
i
If you want to disable the additional ‘Limit channel numbers’ function, repeat
steps 1 to 5 and at step 3 increase the setting to ‘15’.