1. ON/OFF Button
Press POWER button to turn unit on or off.
• In this mode, the fan speed cannot be adjusted, it
starts automatically at a speed according to the
room temperature.
To operate on COOL mode:
• Choose Cool Mode to set the cooling function.
Use the UP (
) and DOWN ( ) buttons to
choose the desired temperature. When Cool
Mode is selected, the fan speed can be adjusted
by pressing the fan button.
To operate on DRY mode:
• In this mode, the air conditioner will generally
operate as a dehumidifi er. Since the conditioned
space is a closed or sealed area, some degree of
cooling will continue. On Dry mode, the fan speed
is not adjustable.
To operate on FAN Only:
• Use this function only when cooling is not desired,
such as for room air circulation or to exhaust stale
air (on some models). (Remember to open the
vent during this function, but keep it closed during
cooling for maximum cooling effi ciency.) You can
choose any fan speed you prefer.
• In Fan only mode, the temperature is not adjusted.
To operate on HEAT mode (Cooling models without):
• Choose Heat Mode to set the heating function.
Use the UP (
) and DOWN ( ) buttons to
choose the desired temperature. When Heat
Mode is selected, the fan speed can be adjusted
by pressing the fan button.
• If the outdoor side temperature is below 41°F, the
machine will shut off and display ‘LO’.
6. TIMER Button
• Press Timer button, the TIMER indicator light
illuminates. lt indicates the Auto Start or Auto
Stop program is initiated. For some units,
continuing to press the Timer button will cancel
the timer settings.
• Press or hold the UP (
) or DOWN ( ) button
to change the Auto time by 0.5 hour increments,
up to 10 hours, then at 1 hour increments up to
24 hours. The control will count down the time
remaining until start.
• The selected time will register in 5 seconds, and
the system will automatically revert back to
display the previous temperature setting or room
temperature when the unit is on. When the unit is
off, there is no display.
• Turning the unit ON or OFF at any time or
adjusting the timer setting to 0.0 will cancel the
Auto Start/Stop timed program.
To cancel timer operation, press and hold the timer
button for 2 seconds until the beep/buzzer is heard.
NOTE
The unit will automatically initiate the Energy Saver
function under Cool, Dry, and Auto modes.
NOTE
Press or hold either UP ( ) or DOWN ( ) button
until the desired temperature is shown on the display.
This temperature will be automatically maintained
anywhere between 60°F (16°C) and 86°F (30°C).
If you want the display to read the actual room
temperature, see “To Operate on Fan Only” section.”
NOTE
2. ECO Button
Press ECO button to initiate this function. This
function is available on COOL, DRY, and AUTO (only
AUTO-COOLING and AUTO-FAN) modes. The fan will
continue to run for 3 minutes after the compressor
shuts off. The fan then cycles on for 2 minutes at 10
minute intervals until the room temperature is above
the set temperature, at which time the compressor
turns back on and Cooling Starts.
Press ECO button for 3 seconds to initiate the fi lter
feature. This feature is a reminder to clean the Air
Filter for more effi cient operation. The LED (the
light above the button) will illuminate after 250
hours of operation.
3. FAN Button
Press Fan button to select the Fan Speed in four
steps - Auto, Low, Med or High. Each time the button
is pressed, the fan speed mode is shifted. For some
models, the fan speed can not be adjusted.
4. UP/DOWN Button
Press UP (
) or DOWN ( ) button to change
temperature setting.
5. MODE Button
To choose operating mode, press the MODE button.
Each time you press the button, a mode is selected
in a sequence that goes from Heat, Auto, Cool, Dry
and Fan. The indicator light beside the button will
be illuminated and will remain on once that mode is
selected. The unit will automatically initiate the Energy
Saver function under Cool, Dry, and Auto (only Auto-
Cooling and Auto-Fan) modes.
To operate on AUTO feature:
• When you set the air conditioner to Auto mode, it
will automatically select cooling, heating or fan only
operation, depending on what temperature you
have selected and the current room temperature.
• The air conditioner will control the room
temperature automatically based on then
temperature you set.
To Next Page
Loading...
