Midea MWAUK-12CRN8-BCJ9 User Manual (English)

Questions and Answers:

B
Bradley KellyAug 15, 2025
What to do if my Midea MWAUK-12CRN8-BCJ9 Air Conditioner does not start?
- S
  Sean StevensAug 15, 2025
  If your Midea Air Conditioner doesn't start, there are several potential causes: * The wall plug may be disconnected. Ensure it's firmly pushed into the wall outlet. * A house fuse might be blown, or the circuit breaker tripped. Replace the fuse with a time delay type or reset the circuit breaker. * The Plug Current Device may have tripped. Press the RESET button. * The power may be off. Turn the power ON.
N
Nicholas GibsonAug 21, 2025
Why does my Midea MWAUK-12CRN8-BCJ9 turn on and off rapidly?
- M
  Mr. Juan WhiteAug 21, 2025
  Your Midea Air Conditioner might be turning on and off rapidly due to: * A dirty air filter restricting airflow. Clean the air filter. * Extremely hot outside temperatures. Set the FAN speed to a higher setting to increase airflow past the cooling coils.
D
Dominique Campbell DDSAug 25, 2025
What causes water to drip inside from my Midea MWAUK-12CRN8-BCJ9 Air Conditioner when it's cooling?
- K
  Kelsey DavisAug 25, 2025
  Water dripping inside from your Midea Air Conditioner when it's cooling is likely due to improper installation. Tilt the air conditioner slightly to the outside to allow for water drainage. Refer to the installation instructions or check with the installer.
P
Pamela WilsonAug 27, 2025
How to fix Midea Air Conditioner when air from unit does not feel cold enough?
- J
  Jeffrey MitchellAug 27, 2025
  If the air from your Midea Air Conditioner doesn't feel cold enough, consider the following: * If the room temperature is below 17°C (62°F), cooling may not occur until the room temperature rises above this level. * The temperature sensor behind the air filter element might be touching the cold coil. Keep it away from the cold coil. * You may need to set the unit to a lower temperature. * If you recently changed modes, the compressor may have stopped. Wait for 3 minutes after setting it to the COOL mode.
T
Thomas PerryAug 30, 2025
Why is my Midea MWAUK-12CRN8-BCJ9 Air Conditioner making noise when cooling?
- B
  Brooke DaltonAug 30, 2025
  If your Midea Air Conditioner is making noise while cooling, it could be due to: * Air movement sound. If it's too loud, set the fan to a slower setting. * Window vibration caused by poor installation. Refer to the installation instructions or check with the installer.
R
Richard WilsonSep 2, 2025
Why is the remote sensing deactivating prematurely on my Midea MWAUK-12CRN8-BCJ9?
- J
  Joseph JohnstonSep 3, 2025
  If the remote sensing is deactivating prematurely on your Midea Air Conditioner (on some models), it could be due to: * The remote control not being located within range. Place the remote control within 20 feet and pointed in the general direction of the air conditioner unit. * An obstruction blocking the remote control signal. Remove the obstruction.
P
Phillip BurkeSep 5, 2025
Why is my room too cold with the Midea MWAUK-12CRN8-BCJ9 Air Conditioner on?
- C
  Charles HughesSep 5, 2025
  If your room is too cold with the Midea Air Conditioner on, it is likely because the set temperature is too low. Increase the set temperature.
T
Theresa RiceSep 8, 2025
Why is my Midea Air Conditioner dripping water outside when cooling?
- P
  Philip GarciaSep 8, 2025
  Water dripping outside from your Midea Air Conditioner when it's cooling is normal during excessively humid days. The unit is removing a large quantity of moisture from the humid room.
A
Antonio StantonSep 12, 2025
What to do if Midea MWAUK-12CRN8-BCJ9 is cooling, but room is too warm and ice is forming?
- S
  Susan BurnsSep 12, 2025
  If your Midea Air Conditioner is cooling, but the room is too warm and ice is forming on the cooling coil, here's what you can do: * If the outdoor temperature is below 17°C (62°F), set the unit to FAN ONLY mode to defrost the coil. * The air filter may be dirty. Clean the filter and set to FAN ONLY mode to defrost. * The thermostat may be set too cold for nighttime cooling. Set to FAN ONLY mode to defrost the coil, then set the temperature to a higher setting.