Midea MWAUK-14.5CRN8-BCK3N User Manual (English)

Questions and Answers:

J
Joshua MezaAug 16, 2025
What to do if my Midea MWAUK-14.5CRN8-BCK3N does not start?
- J
  Joseph KruegerAug 16, 2025
  If your Midea Air Conditioner doesn't start, there are several potential causes: * The wall plug may be disconnected. Ensure it's firmly pushed into the wall outlet. * A house fuse might be blown, or the circuit breaker tripped. Replace the fuse with a time delay type or reset the circuit breaker. * The Plug Current Device may have tripped. Press the RESET button. * The power may be off. Turn the power ON.
K
Katie SantosAug 21, 2025
Why does my Midea MWAUK-14.5CRN8-BCK3N Air Conditioner turn on and off rapidly?
- B
  Bobby PhillipsAug 22, 2025
  Your Midea Air Conditioner might be turning on and off rapidly due to: * A dirty air filter restricting airflow. Clean the air filter. * Extremely hot outside temperatures. Set the FAN speed to a higher setting to increase airflow past the cooling coils.
J
Justin MorganAug 25, 2025
What causes water to drip inside from my Midea MWAUK-14.5CRN8-BCK3N Air Conditioner when it's cooling?
- T
  Tracy CamposAug 26, 2025
  Water dripping inside from your Midea Air Conditioner when it's cooling is likely due to improper installation. Tilt the air conditioner slightly to the outside to allow for water drainage. Refer to the installation instructions or check with the installer.
B
briannacooperAug 28, 2025
How to fix Midea MWAUK-14.5CRN8-BCK3N when air from unit does not feel cold enough?
- C
  Christopher DeanAug 28, 2025
  If the air from your Midea Air Conditioner doesn't feel cold enough, consider the following: * If the room temperature is below 17°C (62°F), cooling may not occur until the room temperature rises above this level. * The temperature sensor behind the air filter element might be touching the cold coil. Keep it away from the cold coil. * You may need to set the unit to a lower temperature. * If you recently changed modes, the compressor may have stopped. Wait for 3 minutes after setting it to the COOL mode.
C
courtneycrawfordAug 31, 2025
Why is my Midea Air Conditioner making noise when cooling?
- J
  Joe Mason IVAug 31, 2025
  If your Midea Air Conditioner is making noise while cooling, it could be due to: * Air movement sound. If it's too loud, set the fan to a slower setting. * Window vibration caused by poor installation. Refer to the installation instructions or check with the installer.
C
Craig MathisSep 3, 2025
Why is the remote sensing deactivating prematurely on my Midea MWAUK-14.5CRN8-BCK3N?
- M
  Monica SmithSep 3, 2025
  If the remote sensing is deactivating prematurely on your Midea Air Conditioner (on some models), it could be due to: * The remote control not being located within range. Place the remote control within 20 feet and pointed in the general direction of the air conditioner unit. * An obstruction blocking the remote control signal. Remove the obstruction.
N
Nicole GrantSep 5, 2025
Why is my room too cold with the Midea MWAUK-14.5CRN8-BCK3N Air Conditioner on?
- K
  kthomasSep 6, 2025
  If your room is too cold with the Midea Air Conditioner on, it is likely because the set temperature is too low. Increase the set temperature.
S
Shelly BerrySep 8, 2025
Why is my Midea MWAUK-14.5CRN8-BCK3N Air Conditioner dripping water outside when cooling?
- J
  Janice MartinSep 9, 2025
  Water dripping outside from your Midea Air Conditioner when it's cooling is normal during excessively humid days. The unit is removing a large quantity of moisture from the humid room.
P
Patrick GarciaSep 12, 2025
What to do if Midea MWAUK-14.5CRN8-BCK3N is cooling, but room is too warm and ice is forming?
- D
  Darryl JenkinsSep 12, 2025
  If your Midea Air Conditioner is cooling, but the room is too warm and ice is forming on the cooling coil, here's what you can do: * If the outdoor temperature is below 17°C (62°F), set the unit to FAN ONLY mode to defrost the coil. * The air filter may be dirty. Clean the filter and set to FAN ONLY mode to defrost. * The thermostat may be set too cold for nighttime cooling. Set to FAN ONLY mode to defrost the coil, then set the temperature to a higher setting.